Dieffematic CENTRALE Mini Schnellstart-Handbuch - Seite 3

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Kontrolleinheit Dieffematic CENTRALE Mini herunter. Dieffematic CENTRALE Mini 4 Seiten.

Seite drucken

CENTRALE Mini

S-0205-00

IMPORTANT WARNINGS

The manufacturer from now declines all responsibility for damage to persons

or things due to improper use of the device, failure to comply with the

instructions herein, incorrect installation or any damage if the electrical

system upstream of the automation does not comply with current regulations.

NOTE:

 Non The centre must not have any type of sectioning

mechanism from the electrical line 230 Vac; it is therefore

the responsibility of the installer to see the installation of

a sectioning device within the plant.

 The correct functionament of S-0205-00 anticipates the

connection of a general safety device with contact (NC).If

not used, this input must be bridged.

 Mono-phase electronic exchange, for the automation of

sliding doors and rolling shutters with an incorporated

radio receiver.

Installation must be performed by qualified technical personnel. Similar

considerations apply to the planning phases and to any necessary maintenance

operations that may be necessary.

COLLEGAMENTI:

MT1

230 Vac input (phase)

230 Vac input (Neutral)

Opening motor output

Common motor output

Closing motor output

Command output for anti-tampering device ("Central MAXI") (device sold

separately).

230 Vac flash input (Phase)

230 Vac flash input (Neutral)

MT2

12 Vac 1 W service feed output.

C. Open-close push button input (NA).

D. Common GND input.

Safety device input (NC).

OPERATIONS:

Operation Step-by-Step:

(REMOTE CONTROL 2 buttons)

The first pulse (by radio control) controls the opening until the operating time lapse; the second

impulse closes the shutter. If a button is pressed before the operating time expires, the control unit

will stop the motion, a further command restarts motion in the opposite direction.

Operation Step-by-Step:

(

REMOTE CONTROL 1 button,

The pulse (by radio control or low voltage button) controls the opening until the operating time lapse;

the second impulse closes the shutter. If the button is pressed before the operating time expires, the

control unit will stop the motion, a further command restarts motion in the opposite direction.

Automatic Closing:

The control unit can close the rolling shutter (when the opening limit switch) automatically without

sending additional commands. The choice of this mode of operation is described in the programming

mode of the automatic closing time.

Security Device:

The control unit allows the supply and connection of photocells, pneumatic edge. The intervention

in the opening phase is not considered, in the closing phase causes the reversal of the motion. This

input (MT2: C-D) if not used must be bridged.

PROGRAMMING THE DEVICE:

Use the SEL and SET keys of the control unit to enable or disable, program a series of functions

FW 3.0.5

MT 1

1 2 3 4 5 6 7 8

MT 2

A B C D E

or low tension button)

and parameters as listed in the table below.

SEL:

Selects the type of function to be memorized, the selection is indicated by a flashing Led. By

repeatedly pressing the button it is possible to choose the desired function (

selection will remain active for 10 seconds indicated by a flashing Led, if no other operations

are executed during this period, the control board will return to its previous state.

WARNING:

During programming, the control panel does not respond to

commands from remote control or low voltage button.

LED N°

DESCRIZIONE

Storing codes Transmitter

Operating time programming

Automatic closing time

"User Present" CLOSE

"User Present" OPEN

Buzzer enabling

Courtesy-Flashing Light

End Run Position.

SET:

programmes the information relative the type of function previously selected with the

SEL button.

Functions with one or two remote control commands (funz. CODE)

It is possible to memorise one or two remote control commands during the programming stage. One

code can be used for a cyclical function (raising/lowering), whilst two different codes allows different

commands, the first for raising and the second for lowering.

With remote control to a single key or the low tension button panel, you will get

the following operation:

By using either the radio control or the low tension button panel to operate the gates, commands will

have the following effect: The first command impulse activates the opening mechanism until time

expiry of the timing motor, the second command impulse closes the gate, if a command impulse is

received before the time expiry of the timing motor, the direction of movement of the mechanism will

be halted.

An additional input determines the restart of the movement in the opposite direction.

Using a remote control with two keys, you will get the following operation:

The first button activates the opening mechanism until time expiry of the timing motor, the second

button closes the gate, if a command impulse is received before the time xpiry of the timing motor,

the direction of movement of the mechanism will be halted.

A further input implements the re-starting of the motion in the opposite direction.

PROGRAMMING:

The transmission code is programmed in the following manner: press the SEL button until the LED

CODE flashes, immediately transmit the pre-selected code with the desired remote control, as

soon as the LED

CODE begins to flash rapidly send the second code to be memorised, when

the LED

CODE remains lit, the programming is complete. If the second code is not sent within

10 seconds the control unit will exit the programming phase and select the function with only one

code of the remote control.

CANCELLAZIONE TELECOMANDI:

To cancel all stored codes press the SEL button and LED

press the SET button for 10 seconds The procedure is now complete and LED

will stop flashing.

(The acoustic signal indicates the success of the operation).

Note:

When 75 codes have been stored all LEDs will flash, indicating that no other codes can be

stored.

rev. 1.0 06/03/2018

7 led

). The

CODE

MOTOR TIME

T. PAUSE

UOMO/CH

UOMO/AP

BEEP

LAMP/CORT

CODE will start to flash. Then

CODE