EPH R17 Betriebsanleitung - Seite 2
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Zeitschaltuhr EPH R17 herunter. EPH R17 2 Seiten. 1 zone timeswitch
Seite druckenR17 - 1 Zone Timeswitch
8. Reviewing the program settings
Lower the cover on the front of the unit.
Move the selector switch to the PROG SET position.
By pressing
this will review each of the ON/OFF times for P1 to P3.
When completed, move the selector switch to the RUN position.
9. Boost function
This function allows the user to extend the ON period for 1, 2 or 3 hours.
If the zone that you wish to Boost is timed to be OFF, you have the
facility to switch it ON for 1, 2 or 3 hours.
ZONE
Press
once, twice or three times respectively.
1
Boost
To cancel the boost function, simply press the
10. Advance function
This function allows the user to bring forward the next switching time. If the
zone is currently timed to be OFF and the ADV is pressed, the zone will be
switched ON until the end of the next switching time. If the zone is currently
timed to be ON and the ADV is pressed, the zone will be switched OFF until
the end of the next switching time.
ZONE
Press
for this function.
1
ADV.
To cancel the ADVANCE function, simply press the
11. Holiday mode
Lower the cover on the front of the unit.
Move the selector switch to the RUN position.
Press the
button.
Holiday
The current date and time will ash on the creen.
It is now possible to enter the date and time when you plan to return.
Press the
or
buttons to adjust the holiday period required.
Press the
button.
The timeswitch is now switched OFF for the selected number of days.
By pressing the
button again, this will cancel the holiday mode,
thereby returning the timeswitch to the normal setting.
12. Backlight mode selection
There are two settings for selection. The factory default setting is ON.
ON
The backlight is permanently ON.
AUTO
On pressing any button the backlight stays on for 10 seconds.
To adjust the backlight setting, lower the cover on the front of the unit.
Move the selector switch to the RUN position.
Press the
button for 5 seconds.
Press either the
or
Press the
button.
CLOCK
SET
ZONE
button again.
1
Boost
ZONE
button again.
1
ADV.
RUN
CLOCK
SET
On
RUN
CLOCK
SET
buttons to select the ON or AUTO mode.
EPH Controls Ireland
[email protected] www.ephcontrols.com
13. Keypad lock and unlock
RUN
PROG
SET
To lock the keypad, press and hold the
5 seconds.
will appear on the screen. The keypad is now locked.
To unlock the keypad, press and hold the
5 seconds.
will disappear from the screen. The keypad is now unlocked.
14. Frost protection function
Selectable range 5~20°C. This function is set to protect pipes against
freezing or to prevent low room temperature when the timeswitch is
programmed to be OFF or is manually OFF.
Frost protection can be activated by following the procedure below.
Move the selector switch to the RUN position.
Press both the
Press either the
protection.
Press the
Press either the
frost protection setpoint.
Press the
Zone 1 will be switched ON in the event of room temperature falling below
the frost protection setpoint.
PROG
SET
When frost protection is enabled, "Frost" will be visible on the screen.
When frost protection is activated, "Frost" will ash on the screen.
15. Master reset
Lower the cover on the front of the timeswitch.
There are four hinges holding the cover in place.
Between the 3rd and 4th hinges there is a circular hole.
Insert a ball point pen or similar object to master reset the timeswitch.
After pressing the master reset button, the date and time will now need
to be reprogrammed.
PROG
SET
EPH Controls UK
[email protected] www.ephcontrols.co.uk
Page 2 of 2
Operating Instructions
Unlocked
and
and
and
buttons for 5 seconds, to enter selection mode.
or
buttons to to turn On or turn O frost
button to con rm.
or
buttons to increase or decrease the desired
button to select.
buttons for
Holiday
buttons for
Holiday
O
RUN
CLOCK
PROG
SET
SET
20180621_R17_InsIns_JW