Olympus E-3 Faq - Seite 25
Blättern Sie online oder laden Sie pdf Faq für Digitalkamera Olympus E-3 herunter. Olympus E-3 26 Seiten. E-3 guide de démarrage rapide (français)
Auch für Olympus E-3: Schnellstart-Handbuch (2 seiten), System Chart (1 seiten), Benutzerhandbuch (17 seiten), Spezifikationen (6 seiten), Spezifikationen (3 seiten), (Schnellstartanleitung (2 seiten), (Französisch) Schnellstartanleitung (2 seiten)
Seite drucken
When my images are displayed on the E-3's LCD screen, there are
blinking black areas in the image. How do I get rid of them?
What you are seeing is a part of the histogram feature. In the lower right corner of the
LCD screen, you will see a little box that says either SHADOW or HILIGHT. The
blinking black regions identify areas in the image that have no detail due to overexposure
(HILIGHT) or underexposure (SHADOW).
The blinking display doesn't mean there is anything wrong with the camera. Like film
cameras, digicams have a limited brightness range within which they can capture images.
If the camera metering is weighted toward the highlights, there will be a lack of shadow
detail. If the camera metering is weighted toward the shadows, there will be a lack of
highlight detail. In bright sunshine, a picture may have areas lacking both highlight and
shadow detail. On a grey, cloudy day, there may be detail throughout the image. The
purpose of the black blinking areas is to give the photographer feedback about the
exposures. If necessary, the photographer can apply options such as AE Bracketing or
Exposure Compensation to reshoot the image.
The SHADOW and HILIGHT views are among seven options that can be selected by
pressing the [
repeatedly cycles through the views, each of which displays different image information.
When I try to use the AE Bracketing function, why do I only get one
frame instead of three?
The camera's Drive mode is set to Single Frame shooting. Configured this way, which is
the default setting, the shutter button must be pressed for each bracketed frame. If the
Drive mode is set to a Sequential Shooting option, then pressing and holding down the
shutter button will cause the camera to shoot all three bracketed frames in one burst. In
(Sequential Shooting H) drive mode, images are captured at a rate of five per
second for as long as the shutter button is held down. In
drive mode, images are captured at the rate (between 1 and 4 per second) registered in
the
To change the Drive mode, do the following:
1. Press the [
on the top of the camera. It is the middle of the three buttons to the left of the hot
shoe when the camera is held so that the LCD faces the photographer. (This is the
same button used to switch shooting modes.)
2. Using the sub dial to move the cursor, select either
3. Press the [
On the E-3's LCD screen, I see the message "Internal camera
temperature is too high. Please wait for cooling before camera use."
Then the camera shuts off. What causes this message to appear?
As a safety measure, the E-3 issues this message and shuts itself off whenever its internal
temperature climbs too high. This may happen after frequent or continuous use of Live
View or a shooting mode that captures many images in a short time, such as the
Sequential Shooting drive mode. In these situations, the image sensor may not get a
chance to cool off in between shots. The heat of the sensor raises the camera's internal
temperature. If it gets high enough, the camera must turn itself off. Once the camera
has cooled for a few minutes, you will be able to resume shooting.
©2008 Olympus Imaging America Inc.
] button while displaying images in Playback mode. Pressing [
INFO
function, located in the
] (Remote control/Self-Timer/Sequential shooting) button, located
i
] button to activate the new Drive mode.
menu.
Page 25 of 26
D I G I T A L T E C H N I C A L S U P P O R T
O L Y M P U S I M A G I N G A M E R I C A I N C .
( 8 8 8 ) 5 5 3 - 4 4 4 8
h t t p : / / s u p p o r t . o l y m p u s a m e r i c a . c o m
INFO
(Sequential Shooting L)
or
.
Last updated on February 28, 2008
]