Olympus Stylus 820 Gebrauchsanweisung - Seite 2

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Digitalkamera Olympus Stylus 820 herunter. Olympus Stylus 820 5 Seiten. Ikelite digital camera housing

Seite drucken

C C l l o o s s i i n n g g t t h h e e H H o o u u s s i i n n g g

1 . Place housing face down in your

lap or on flat surface.

2. Check to see that there is an

o-ring on the housing back and

that it is clean and in its proper

location.

3. Guide the back onto the housing.

The o-ring should touch the

housing all the way around. There

should be an even gap all the way

around between the housing and

the housing back.

4. Lift the lid snaps so they are

extended and place the lid

snap into the hook on the

housing back.

5. To close the housing push

down on the lid snaps until

they snap into place . Lid

snaps on opposite sides of the

housing should be closed at the

same time. Be sure they are down

far enough to engage the lock.

D D o o u u b b l l e e c c h h e e c c k k - Once the housing is closed, check the o-ring seal.

Check the gap between the housing back and the housing, it

should be even all the way around.

Look through the clear plastic back at the o-ring. You should see

a darkened area where the o-ring is compressed against the

housing back. If you do not see an even black compression seal

all the way around the back, open the lid snaps, reseat the

housing back and close the lid snaps. Visually check the seal again.

L L u u b b r r i i c c a a n n t t s s

1 . Ikelite provides silicone lubricant with the housing. We recommend

you use only Ikelite lubricant on Ikelite products as some other

brands may cause the o-ring to swell and not seal properly.

2. Use only enough lubricant to lightly cover control shafts and

o-rings. Wipe off any excess lubricant with a clean cloth.

Lubricant is not a sealant, it is used to reduce friction. Excessive

lubricant can collect sand and dirt which may interfere with

proper sealing.

C C A A U U T T I I O O N N

N N e e v v e e r r u u s s e e s s p p r r a a y y l l u u b b r r i i c c a a n n t t s s a a s s t t h h e e p p r r o o p p e e l l l l a a n n t t i i n n g g r r e e d d i i e e n n t t c c a a n n

c c a a u u s s e e t t h h e e p p l l a a s s t t i i c c h h o o u u s s i i n n g g t t o o c c r r a a c c k k . .

housing back

o-ring

housing back

even gap

all 4 sides

o-ring

C C h h e e c c k k i i n n g g C C o o n n t t r r o o l l s s

Once the housing has been closed, make sure the housing controls

line up with the camera's controls. If the housing controls are

misaligned slightly make sure the camera hold down bolt has been

tightened down firmly so the camera is flat against the tray.

T T u u r r n n C C a a m m e e r r a a O O n n

Turn the camera on and operate each of the housing controls to

get a feel for using the camera in the housing. Take a few pictures

above water with the camera in the housing.

U U s s i i n n g g F F l l a a s s h h

U U s s i i n n g g t t h h e e C C a a m m e e r r a a ' ' s s B B u u i i l l t t - - i i n n F F l l a a s s h h . .

If you do not have an external flash, the camera's built-in flash

can be used. See Diffuser instructions.

NOTE: The camera's built-in flash cannot be used with optional

Wide-angle lenses.

D D i i f f f f u u s s e e r r a a n n d d D D e e f f l l e e c c t t o o r r I I n n s s t t a a l l l l a a t t i i o o n n

Deflector

Housing shown with

Deflector installed.