Olympus CK2-TRC Anleitung Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Anleitung Handbuch für Mikroskop Olympus CK2-TRC herunter. Olympus CK2-TRC 15 Seiten.
Seite drucken
BEFORE USE
D
Operait,",on!ii:===~
I
A$
iiJ
microscope
is;
a precision innrument, always
handle it
with the care it deserves and avoid abrupt
motions
and 5hocb.
2
When you retnO\le the
mICroscope Irom
the
styrofOilm
CCI5f!,
hold
the
stage
legs
at
A
and
B
(Fill 11
3 For mcwemefll of the microscope, hold
the
stage leg A
and
lhe
observation
lube
C
Do nol hold the
lamp hous-
ing pillar. (Fig. 11
4 The light
source
incorPOriltflS a 6 V 20W halogen bulb.
00
not use any
olher bulb.
5 Avoid expO$Ure of the microscope to dirK! sunlight, high
temperature and humidity, dUSI and vibration.
00 Before use, ascertain thaI the line voltage selector switch
at the base plate of the microscope Stand is SIlt in con-
formity wIth
the
local line Yoltage.
.. Specifications of the eleetrical components differ from
others than the equipment with 12QV of supply circuit,
aI
the eq.,ipment is in compliance with the reQUirements
of Underwriull
Labor"o,i~.
Also,
the equipment is
not needed to
$~ect
volt• .
7 Before fuse replacement, dIsconnect the
pawer
cord from
the AC outlet. The fuse
boK
1 IS Iocilted at the back
of the micrOSCOPe stand. IF'9
21
Use
a scre.vdnYllJ
10
remove
this
boK
• Always Qfound the micrOSCOPe.
A
Fig 1
Fig 2
:s'
c
•
II
Maintenance and
sto~
CD
lens surfaces must ajways
be
kept clean F,ne dust on lens surfaces should
be
blOWll off
by means of
Mild
blower Carefully Wipe off
011
or flngerpnnts on the lens surfaces with gauze ffiOlstened WIth a small
amount of alcohol and ether
(3
7)
m1lrture, or xylene
Do not use organiC solutions to wipe the surfaces of vanous components Plastic parts. especlllily. should
be cleaned With a neutral detergent
@
Be careful not to spill the culture solution, etc. If spilled. It should be Wiped off immediately.
®
When objectives are not screwed Into the nosepiece apertures. seal the apertures With dust plugs, which
Will protect the lenses located In the lower light path from dust. culture solution, etc.
@
When not In use, the microscope should be covered WIth the dust cover provided.
@
A tenSion adjustment ring
CD
IS provided neKt to the coarse
focus adjustment knobs With thiS deVIce the tenSion of the
coarse adjustment
IS
freely adjustable lor elther heavy
Of
IlQht
movement. depending upon operator prelerence (Fig 3)
Applying the tiP of
a
large screwdriver at
a
groove In the
penphery
01
the tenSIOn adjustment
nng
CD.
rotate the
flng
In
the d,rectlon of the arrow to Increase the tensIOn.
Of
feverse
the
flng
to loosen,
However,
do
not
loosen the
lenslOfl adJustment
nng
tOO
much.
because thiS
may
cause the line locus adjustment knobs to
slip.
Fig 3