Accuphase AD-20 Gebrauchsanweisung - Seite 2

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für E/A-Systeme Accuphase AD-20 herunter. Accuphase AD-20 2 Seiten. Analog disc input board

Seite drucken
Accuphase AD-20 Gebrauchsanweisung
Analog Disc Input Board
Thank you for selecting the Accuphase AD-20 Analog Disc Input Board. This option board is
designed for installation in one of the option slots on the rear of an Accuphase component. It
provides a set of inputs for signals from an analog record player.
Usage details of the board will differ, depending on the Accuphase component in which the
board is installed. To ensure correct use, please read this document first and then refer to the
instruction manual of the Accuphase component for additional information.
LEFT, RIGHT analog record player input jacks
Connect the output cable from the analog record player
to these jacks.
GND terminal
Connect the ground cable that emerges from the ana-
log record player to this terminal.
DIP switches S1, S2, S3, S4
Set these switches to the required positions before inserting the board.
Note:
Use a sharp pointed object to move the switch levers and make sure that the levers are set fully
to one side. If a lever is set only half-way, correct operation is not possible.
S １   ：  MC LOAD
MC input impedance selector:
10/30/100 ohms
S ２ , S ３   ：  FILTER
Subsonic filter on/off
S ４   ：  MC/MM selection
If the component where the board is installed
has an MC/MM selector on the front panel,
there is no need to set the S4 switch.
● 
S1: MC LOAD − MC input impedance selector
1
Factory default
ON
setting
100Ω
1, 2, 3, 4 : OFF
1
2
3
4
ON
1, 2 : ON
30Ω
3, 4 : OFF
1
2
3
4
ON
3, 4 : ON
10Ω
1, 2 : OFF
1
2
3
4
Usage
＊ In components with two slots, two boards can be installed.
ON
S2
ON
1
2
3
4
OFF
FILTER
S1
ON
ON
S3
MC LOAD
1
2
3
4
OFF
MC
ON
S4
1
2
MM
AD-20 component side (location of switches S1 - S4)
＊ The S1 setting affects both the left and right channels.
As a general guideline, set this switch as follows :
For MC cartridges with internal impedance of 20
ohms or more : 100 ohm position
For MC cartridges with internal impedance of less
than 20 ohms : 30 ohm or 10 ohm position
Generally, the input impedance setting should be
 ●
about 2 to 3 times the rated cartridge impedance.
However, since the requirements of some car-
tridges may vary, the final setting should be deter-
mined by ear.
AD-20
● 
2
S2, S3: FILTER − Subsonic filter on/off
ON
OFF
1
2
3
ON
ON
1
2
3
● 
S4: MC/MM − Equalizer gain selection
3
ON
MM
1
2
ON
MC
1
2
Caution
Do not touch circuit components, solder areas, or exposed parts of connectors,
to prevent possible damage and contact problems. Hold the board only at the
PCB edges or the rear panel.
1
Set the power switch of the Accuphase compo-
nent to OFF.
2
On the rear panel, loosen the two screws at the
top and bottom and remove the panel covering
30
10
ON
one option slot (see Figure 1).
1
2
3
4
3
Insert the option board by sliding it into the top
and bottom guide rails of the slot (see Figure 2).
When the board touches the internal connector,
give it a slight push until the board is firmly seated.
(The board must be flush with the panel.)
4
Secure the board with the two screws at the top
and bottom.
Caution
 
●
 
●
J091X
INSTRUCTION MANUAL
＊ Be sure to set both the S2 and S3 switches to the same position.
Factory default
setting
1, 2, 3, 4 : OFF
This filter has a cut-off frequency of 25 Hz and a steep
4
attenuation slope of -12 dB/octave. lt cuts off unwanted
subsonic signal components without affecting the audible
1, 2, 3, 4 : ON
range.
4
＊ The S4 setting affects both the left and right channels.
MM: Use this position for moving magnet cartridges with high output
Factory default
setting
Gain: 36dB
1, 2 : OFF
Input Impedance : 47 kohms
MC: Use this position for moving coil cartridges with low output
Gain : 62dB
1, 2 : ON
Input Impedance : As selected with S1
Installation
Before inserting or removing an option board, be sure to turn the power of the
Accuphase component off to prevent the risk of damage.
Tighten the two fastening screws firmly. If the screws are not properly secured,
ground connection will be impaired and damage may occur.
ACCUPHASE LABORATORY, INC.
2-14-10, SHIN-ISHIKAWA, AOBAKU, YOKOHAMA 225-8508, JAPAN
＊ The illustration shows the E-560.
Guide rail
72
4-
00
72
4-
19
00
-0
0
20
-0
0
Sub
Option
panel
board
Guide rail
Fig. 1
Fig. 2
820-3236-10（B3）  Printed in Japan