ARC Audio X2 1100.5 Benutzerhandbuch - Seite 6
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Verstärken ARC Audio X2 1100.5 herunter. ARC Audio X2 1100.5 12 Seiten. Full-range class d amplifier
Seite drucken
Speaker Output Connections
This amplifier features a multi-channel design. This means,
CH1
CH3
it has more than one pair of speaker outputs. It is equipped
with set of removable plug-style terminals for speaker wire
connections up to 14 AWG in size. Make these connections
carefully and neatly. Strip the wire back 5/16", twist the
exposed leads together tightly, and insert them into the block
terminal while being careful that there is no loose or frayed
strands of wire touching adjacent wires or connections.
CH2
CH4
Tighten the flat-head set screw on the terminal until the wire
is held in place securely. The amplifier will go into protection if
the wires ever come in contact
Power, Ground and Turn-On Connections
The X2 1100.5 features a terminal block that is designed to
secure 4 AWG power and ground connections to the amp. We
recommend the use of pure copper power and ground wires in
order to achieve the most reliable connections. Also, be weary
of 4 gauge versus 4-AWG wire. The American Wire Gauge
(AWG) is a universal standard that specifies the diameter of
stranded conductors. Wiring that is labelled as '4 gauge' may
not be adequate to supply the amp with the current it requires
to operate reliably and efficiently.
The Turn On input should be connected to the amplifier +12V
DC remote turn-on output of your after-market source unit. In most cases this is a blue wire with a white stripe. Note: On
some source units, there are power antenna AND remote turn-on wires. If you only hear audio when listening to the AM/
FM tuner, your amp may connected to the wrong wire.
Fuses
The X2 1100.5 includes three 30 amp ATC/ATO fuses on the
left side of the end-panel. These fuses exist to protect the
internal circuitry of the amplifier from damage and are not a
replacement for a proper fuse at the battery in your vehicle.
Under no conditions should you increase the value of the
fuses used in this location.
If the fuses blow immediately upon insertion, contact your
authorized ARC Audio dealer or the Technical Support
department at ARC Audio for assistance.
Auto Sense Turn-On Detection
The X2 1100.5 features two Auto-Sense Turn-On modes. In
DC Detect mode, the amplifier monitors the Channel 1 RCA
input for the presence of a DC offset voltage (common with
Bridge Tied Load (BTL) source units and amplifiers). When
this DC voltage is present, the amp will turn itself on.
When set to Signal Detect, the X2 1100.5 monitors the
Channel 1 RCA input for the presence of an audio signal.
When an audio signal is present, the amp will turn itself on.
The amp automatically turns off 10 seconds after the DC
Detect or Signal Detect no longer sees an appropriate signal.
When using either Auto-Detect mode, only the Channel 1
input is monitored.
The Turn On input on the power terminal block is NOT
used when Auto Detect is turned on.
Page 6
SUB
CH1
CH2
CH 1/2
HP
LP
BANDPASS
FREQ Hz
FREQ Hz
OFF
ON
(CH 1/2)
SIGNAL
DETECT
DC DETECT
Auto-Detect Monitors
CH3
CH4
CH 3/4
CH1-2
LP RANGE
X1
LOW-BP
FULL
X10
HIGH
AUTO SENSE
INPUT
SELECT
OFF
CH1-2
SUB
Channel 1 ONLY
CH1
CH3
SUB
CH2
CH4
Not Used with
Auto-Detect
CH1
CH3
CH2
CH4
CH3
CH1-2
CH3-4