Arcam MARC Amplifier Handbuch - Seite 13

Blättern Sie online oder laden Sie pdf Handbuch für Verstärken Arcam MARC Amplifier herunter. Arcam MARC Amplifier 14 Seiten.

Seite drucken

MARC amplifier - Advanced features

CAUTION

If you intend to change any of the settings described on this

page, please read the following notes thoroughly to familiarise

yourself with the process before amending the settings.

To access the zone control menus....

Zone Group

MODE

CONFIRM

Control

Access

Advanced Setup

CONFIRM to exit

PRESS BOTH BUTTONS AT THE

SHOWS FOR 2 SECONDS

SAME TIME FOR 1 SECOND

SET UP MENUS

Maximum Volume

This control restricts the overall volume level in each zone to a

pre-set maximum.This takes priority over any other setting.

Once you have accessed the zone you wish to change, turn the

volume control knob.The volume bar graph will show the

maximum volume level in the selected zone. Press CONTROL

to move further through the menus, or MODE to stay on this

menu, but move to a different zone.

Lock Volume

When on, this control locks the current volume in each

zone so that it cannot be changed.The MUTE control will still

work within each zone.Turn the VOLUME control knob to

change from YES to NO or vice versa. Press CONTROL to

move further through the menus, or MODE to stay on this

menu, but move to a different zone.

Access

This selects which entertainment source can be played or

accessed in each zone. Press the source buttons

to select

one or several entertainment sources you want the zone to

have access to.The green LED light above the button will show

the selections you have made.

Press CONTROL to move further through the menus, or

MODE to stay on this menu, but move to a different zone.

Control

This selects which entertainment source can be controlled in

each zone. Press the source buttons

to select one, or

several entertainment sources you want the zone to control.

The green LED light above the button will show the selections

you have made. Press CONTROL to move further through the

menus, or MODE to stay on this menu, but move to a

different zone.

Zone group

Zone grouping allows you to lock several zones to the same

source - if you change the source in one of these zones, all

zones in the group change as well.The volume controls are

independent. A typical application would be for bedroom with

en-suite bathroom.

Returning to factory settings

If you have a system setting problem and you want to clear all

settings back to factory defaults, press and hold both CD and VCR

buttons on the amplifier for 5 seconds.The display will show the

power on screen 'Arcam Multiroom Amplifier' to confirm that your

settings have been cleared.

Zone 3

CONTROL

MODE

Zone 3

Lock V

Lock Vol

olum

ume

Zone 3

Max Vol

Max V

olum

ume

Zone 3

TO CYCLE THROUGH

PRESS TO

8 MENUS OF

MENUS, PRESS

CYCLE THROUGH

CONTROL REPEATEDLY

ZONES 2-5

ZONE OPTIONS

To put a zone in a group, use the VOLUME control knob

Options are 'None', 'Group A' or 'Group B'.

Power On source

When the unit is powered up, or a zone comes out of standby

a power on source is selected.

Use the source buttons

to set the power on source for a

given zone. Pressing any source button twice selects 'Previous'

i.e. the source which was active before standby or power down.

Power On volume

When the unit is powered up, or a zone comes out of standby

a power on source is selected.

This can be changed as follows:

Use the VOLUME control knob

to set the power on

volume.Turning the volume down below minimum sets it to

'Previous'. Note that if Lock Volume (see above) has been set,

then the power on volume always shows 'Previous'.

Standby rights

As shipped from the factory, the entire system can be placed

into standby by pressing and holding the standby/power button

in a zone.This menu allows you to block this operation.

Note that all zones are always able to bring the system out

of standby.

Use the volume control knob

to change the standby rights.

Options are 'Local only' or 'Local + all off '.

To exit the set up menus press CONFIRM

at any time.

Safety Guidelines

SAFETY IN USE

SAFETY STANDARD

This product has been designed to meet the EN60065

international electrical safety standard.

SAFETY INSTRUCTIONS

This product was designed and manufactured to meet strict quality

and safety standards. There are, however, some installation and

operation precautions of which you should be particularly aware:

CONFIRM

1. Read Instructions All the safety and operating

instructions should be read before the appliance is operated.

2. Retain Instructions The safety and operating

instructions should be retained for future reference.

3. Heed Warnings All warnings on the appliance and in this

TO EXIT THE

handbook should be adhered to.

MENU AT ANY

TIME, PRESS

4. Follow Instructions All operating and use instructions

should be followed.

5. Water and Moisture The appliance should not be used

near water - for example near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement or near a swimming pool, etc.

6. Racks and Stands The appliance should be used only

with a rack or stand that is recommended for use with audio

equipment. If the equipment is on a portable rack it should be

moved with care. Quick stops, excessive force, and uneven

surfaces may cause the combination to overturn.

7. Ventilation The appliance should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the appliance should not be situated

on a bed, sofa, rug or similar surface that may block the

ventilation openings or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air through

the ventilation openings. We recommend a minimum distance

of 50mm (2 inches) around the sides and top of the apparatus

to provide adequate ventilation.

8. Heat The appliance should be situated away from naked

flames and equipment, heat such as radiators, stoves or other

appliances (including other amplifiers) that produce heat.

9. Power Sources The appliance should be connected to a

power supply only of the type described in the operating

instructions or as marked on the appliance.

10. Grounding Precautions should be taken so that the

grounding means of the appliance is not defeated.

11. Power-Cord Protection Power supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular

attention to cords and plugs, and the point where they exit

from the appliance.

12. Cleaning Unplug the unit from the mains supply before

cleaning. The appliance should normally only require a wipe

over with a clean, dry, lint-free cloth. If it is heavily soiled then a

cloth slightly dampened with a water/washing up liquid solution

may be used. Dry the unit afterwards with a dry cloth.

We do not advise the use of furniture type cleaning sprays/

polishes as this can cause white marks, which are very difficult

to remove, if the unit is then wiped over with water.

13. Power Lines An outdoor antenna/ aerial should be

located away from power lines.

14. Non-use Periods If the unit has has a standby function,

a small amount of current will continue to flow into the

equipment in this mode.The power cord of the appliance

should be unplugged from the outlet when left unused for a

long period of time.

15. Object and Liquid Entry Care should be taken so

that objects do not fall and liquids are not spilled into the

enclosure through any openings. Objects filled with liquids, such

as vases, should not be placed on the equipment.

16. Abnormal Smell If an abnormal smell or smoke is

detected from the appliance, immediately turn the power off

and unplug the unit from the wall outlet.

Contact your dealer immediately.

17.Damage Requiring Service The appliance should be

serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged or,

B. Objects have fallen, or liquid has spilled into the appliance or,

C. The appliance has been exposed to rain or,

D. The appliance does not appear to operate normally or exhibits

a marked change in performance or,

E. The appliance has been dropped or the enclosure damaged.

18. Servicing You should not attempt to service the appliance

beyond that described in this handbook. All other servicing

should be referred to qualified service personnel.

19. Climate The appliance has been designed for use in

moderate climates.This appliance is normally supplied with a

moulded mains plug already fitted to the lead. If for any reason

the plug needs to be removed, it must be disposed of

immediately and securely, as it is a potential shock hazard when

inserted into a mains socket.

ELECTRICAL CONNECTIONS

This appliance is normally supplied with a moulded mains plug

already fitted to the lead. If for any reason the plug needs to be

removed, it must be disposed of immediately and securely, as it is a

potential shock hazard when inserted into a mains socket.

Warning: This appliance must be earthed.

If the plug is removed then the remaining lead must be rewired as

follows:

The green and yellow

The blue wire

wire must be connected

must be connected

to the terminal which

to the terminal

is coloured green and

which is coloured

yellow, or marked with

blue or marked

the letter E or the

with the letter N.

safety earth symbol.

The brown wire must be

connected to the terminal

which is coloured brown or

marked with the letter L.

When replacing the fuse in the supplied moulded mains plug, the

integral fuse holder/cover must always be refitted.

Use a 5 amp fuse.