AXTON A101 Handbuch für Installation und Betrieb - Seite 6
Blättern Sie online oder laden Sie pdf Handbuch für Installation und Betrieb für Auto-Empfänger AXTON A101 herunter. AXTON A101 18 Seiten. 1-/2-/4-/6-channel power amplifiers
Seite drucken
A601 CONNECTIONS + CONTROLS
1
INPUT SIGNAL SELECTION
Slide switch to select the input signal for all channels. "2-CH" to use only CH1/CH2 input
terminal for all output channels. "6-CH" to give each output channel its corresponding
input channel.
2
AUTO-TURN-ON MODE
Slide switch to select the auto-turn-on function: REM by remote wire, VOX to switch on
by music signal or DC by DC offset signal of the head units integrated amplifier.
3
INPUT SENSITIVITY CONTROL CH1/CH2
Input gain potentiometer "SENS" for channel CH1/CH2, to match the output voltage of
the head unit to the amplifier's input.
4
OPERATION MODE SWITCH CH1/CH2
Slide switch to select the operation mode of the X-over for section CH1/CH2 of the
amplifier: Highpass [HPF], Lowpass [LPF] or full signal [FULL].
5
X-OVER FREQUENCY CONTROL CH1/CH2
Control potentiometer to adjust the highpass or lowpass filtering frequency for section
CH1/CH2 of the amplifier.
6
INPUT SENSITIVITY CONTROL CH3/CH4
Input gain potentiometer "SENS" for channel CH3/CH4, to match the output voltage of
the head unit to the amplifier's input.
7
OPERATION MODE SWITCH CH3/CH4
Slide switch to select the operation mode of the X-over for section CH3/CH4 of the
amplifier: Highpass [HPF], Lowpass [LPF] or full signal [FULL].
8
X-OVER FREQUENCY CONTROL CH3/CH4
Control potentiometer to adjust the highpass or lowpass filtering frequency for section
CH3/CH4 of the amplifier.
9
POWER LED
LED to show the operating status of the amplifier by blue/red illumination. Blue is normal
working state, red is protect mode of amplifier.
10 SIGNAL INPUTS FRONT CH1/CH2
Low-level stereo RCA signal or high-level speaker signal input terminal for connection to
head-unit.
11 SIGNAL INPUTS FRONT CH3/CH4
Low-level stereo RCA signal or high-level speaker signal input terminal for connection to
head-unit.
12 INPUT MODE SELECTION CH1/CH2/CH3/CH4
Switch to select the proper input sensitivity range: RCA signal input = Low. Speaker
signal input = Hi.
13 SIGNAL INPUTS FRONT CH5/CH6
Low-level stereo RCA signal or high-level speaker signal input terminal for connection to
head-unit.
14 INPUT MODE SELECTION CH5/CH6
Switch to select the proper input sensitivity range: RCA signal input = Low. Speaker
signal input = Hi.
15 INPUT SENSITIVITY CONTROL CH5/CH6
Input gain potentiometer "SENS" for channel CH5/CH6, to match the output voltage of
the head unit to the amplifier's input.
–
–
10
A601 CONNECTIONS + CONTROLS
16 OPERATION MODE SWITCH CH5/CH6
Slide switch to select the operation mode of the X-over for section CH5/CH6 of the
amplifier: Highpass [HPF], Lowpass [LPF] or full signal [FULL].
17 X-OVER FREQUENCY CONTROL CH5/CH6
Control potentiometer to adjust the highpass or lowpass filtering frequency for section
CH5/CH6 of the amplifier.
18 SPEAKER OUTPUT TERMINAL
Output terminal to connect the speakers to the amplifier in either stereo or bridged
mode.
19 "+12 V" POWER INPUT TERMINAL
Terminal to connect the amplifier to the positive +12V pole of the car battery.
20 "REM" INPUT TERMINAL
Terminal to connect the amplifier to the automatic (remote) turn-on / turn-off lead of the
head unit. You must switch
to "REM" when using the remote wire input terminal.
2
21 "GND" POWER INPUT TERMINAL
Terminal to connect the amplifier to the chassis ground or negative pole of the car
battery.
1
2
3 4 5 6 7 8
bl
bm bn
bt
9
bo bp
bq
br
bs
bu cl
cm
–
–
11