Arcam CD93 Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Handbuch für CD-Spieler Arcam CD93 herunter. Arcam CD93 8 Seiten.

Seite drucken

Using the remote control

CR-314 Remote Control

Note that greyed-out buttons on the remote control are DVD-

specific and are not used with the CD player.

Ensure that CD mode is selected using the

toggle button. The 'CD' LED above the

button is lit briefly when CD mode is selected.

Turns the display on or off. Turning the display off generally

produces a slight improvement in sound quality.

This button enables you to repeat any section of music within

a track. Whilst the disc is playing, press the

start of the section you wish to repeat. 'REPEAT' is shown on

the display and the letter 'A–' flashes. Press the button a second

time when you reach the end of the section you wish to repeat.

The 'A–B' letters stop flashing and remain lit. This section will

repeat until you press

(

) moves forward within the selected loop.

To repeat the entire CD or a pre-programmed selection of tracks

press

once: 'REPEAT' lights on the display. To repeat a

RPT

particular track, select that track and then press

that 'REPEAT 1' is shown on the display.

different track, that track is repeated instead.

To cancel the repeat function press

Search backwards and forwards;

Skip track backwards and forwards (see page 5)

Pause, Play and Stop (see page 5)

Press once to shuffle play CD tracks (i.e. play them in

a random order). Press again to cancel shuffle play.

Press

TITLE

once to display the remaining time of the currently

playing track. Press again to display the time remaining of

the disc. Press a third time to turn the text display on.

Press

again and the display reverts to its original setting,

TITLE

showing the time elapsed for the current track.

For CDs with text, pressing

is loaded but not playing displays the artist's name.

Pressing

a second time displays the total number of

TITLE

tracks and the total playing time.

CD93

CD/DVD

DISP (display)

A–B

button at the

. The forward search button

RPT (repeat)

RPT

twice so

If you now select a

a third time.

RPT

Search and Skip Track

OPEN

Opens and closes the CD tray

Playback control

P MODE

TITLE

once while the disc

CD/DVD REMOTE

DVD

DISP

A-B

RPT

CLEAR

PROG

OPEN

MUTE

SUBT

TITLE

MODE

ZOOM

AUDIO

MEM

RTN

ANGLE

SETUP

STATUS

SRCH

CR-314

0–9 keypad

This allows direct access to individual tracks on the disc.

To select a track, press the corresponding keypad button.

For tracks greater than 9, enter the digits in sequence. For

example, to play track 15, press and hold

the display moves to the left, then press

CLEAR

If you make a mistake whilst programming you can delete

the last entered track by pressing

the programmed tracks, press

CLEAR

displayed.

To exit the program facility, press

PROG (Program)

You can program a selection of up to 24 tracks from a

disc to play in any order. Select a track by using the

and

buttons, then press

PROG

memory ('PROGRAM' appears on the display to indicate that you

have started programming a sequence). Repeat these steps to

program the remaining tracks in your selection. Alternatively,

press

once and enter your track selection using the 0–9

PROG

keypad.

The display shows the track numbers programmed, the total

length of the programmed sequence and the number of tracks

programmed (shown by a number below the word 'STEP').

Each time you enter a track the number below 'STEP' increments

by one and flashes until you press

press

within about five seconds the display stops flashing

PROG

and you will have to reselect the track.

Press

to play the program. Press

sequence from the start. Press and hold

programmed sequence. Press

PROG

facility.

MUTE

Stops sound to the speaker outputs of certain Arcam amplifiers.

Volume +/–

Adjusts the volume on Arcam remote-controllable amplifiers.

Note that the volume (+/–) controls and

no effect on the audio output level of the CD players.

NOTE: Remember to install the two AAA batteries supplied

before trying to use your remote control.

Do not place anything in front of the display area on the

CD player (where the IR receiver is located), or the remote

control may not work.

until the number on

CLEAR

. To delete all

repeatedly until '0' is

PROG

to program the track into

to confirm. If you fail to

PROG

again to replay the entire

to erase the

CLEAR

again to exit the program

button have

MUTE