5. Press the d button until
then press
. Press
Menu
the power cleaning.
6. Follow the instructions on the LCD display to raise or lower
the ink levers.
7. When cleaning is finished and the
flashing, print the nozzle check again to confirm that the
head is clean.
For effective cleaning, always run a nozzle check between
cycles.
If the pattern is still missing segments or has deflections
after a power cleaning cycle, turn the printer off and leave it
overnight. Then clean the print head again the following
morning with regular cleaning cycles. If you still see no
improvement, contact Epson for assistance.
Aligning the Print Head
Aligning the print head is the most important thing you can
do to ensure the best print quality. If banding appears on your
prints, if they look grainy or blurry, or you see misregistration
or "ghosting," you may need to align the print head.
Although you can align the print head using the printer utility
software, it's also easy to align from the control panel. This
will do the most thorough job in the shortest time, and it's all
automatic.
If you haven't already done so, it's a good idea to run a nozzle
check before aligning the print head (see page 6). This ensures
that the print head alignment patterns print correctly.
Follow these steps to align the print head using the control
panel:
1. Make sure the printer is turned on. Then load Epson
Enhanced Matte, Doubleweight Matte, Premium Luster
Photo paper, or the paper that came with the printer.
2. Press the
button.
Menu
3. Press the d button until
highlighted, then press
highlighted.
4. Press
. The
Menu
STANDARD
This is the correct thickness setting for most Epson papers.
5. Press
to save the setting.
6. Press l, then press d to highlight
7. Press the
button to highlight
Menu
again.
(uni-directional) is highlighted. This is
Menu
UNI-D
the type of alignment to start with.
is highlighted,
PWR CLEANING
again, then press
Menu
Pause light stops
is
HEAD ALIGNMENT
Menu. PAPER THICKNESS
setting is selected by default.
.
ALIGNMENT
, then press
AUTO
8. Press the
to start
Each head alignment takes about 7 minutes. The printer's
white beam sensor reads the alignment pattern and adjusts
the printer automatically. Make sure you don't open the
front cover or turn off the printer during this process.
9. When the uni-directional alignment is finished, press the d
button until
button to start the bi-directional black alignment
process.
10. When the bi-directional black alignment is finished, press
the d button until
button to start the alignment process.
11. When done, press the
alignment mode.
If you want to verify or fine-tune the automatic alignment
process, you can perform a manual head alignment. See your
electronic Reference Guide for instructions.
Replacing the Cutter Blade
If you notice that your paper isn't cut cleanly, the cutter blade
may need to be replaced. For a list of media that are not
recommended for use with the cutter, see the Printer Guide.
You can check the status of your cutter by printing a status
sheet. See page 5 for instructions. You can obtain a new cutter
blade from Epson (part number C12C815291).
Removing the Old Blade
1. Press the
2. Press the d button until
then press
3. Press
Menu
4. Press the
replacement position.
CUTTER REPLACEMENT LABEL
5. Open the front cover.
is
8/05
Epson Stylus Pro 7800 and 9800
button to start the alignment process.
is highlighted. Then press the
BI-D 2-COLOR
is highlighted. Then press the
BI-D ALL
Pause button to exit head
button.
Menu
MAINTENANCE
.
Menu
again to select
CUTTER REPLACEMENT
button. The print head moves to the
OPEN FRONT COVER TO SEE
is displayed.
Epson Stylus Pro 7800 and 9800 - 7
is highlighted,
.
Seite drucken