Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Handbuch - Seite 15

Blättern Sie online oder laden Sie pdf Handbuch für Drucker Epson C11C640001 - LX 300+II B/W Dot-matrix Printer herunter. Epson C11C640001 - LX 300+II B/W Dot-matrix Printer 17 Seiten. Epson lx-300: user guide
Auch für Epson C11C640001 - LX 300+II B/W Dot-matrix Printer: Benutzerhandbuch (50 seiten)

Epson C11C640001 - LX 300+II B/W Dot-matrix Printer Handbuch

Clearing a Paper Jam

If paper becomes jammed in the printer, follow these steps to
remove it:
1. Turn off the printer, open (or remove) the printer cover,
and remove the paper guide.
2. If continuous paper is jammed in the printer, tear off the
fresh supply at the perforation nearest the paper entry slot.
3. Gently remove any paper inside the printer, including any
torn pieces. You can use the knob on the right side of the
printer to help feed the paper out.
Use the paper feed knob to clear paper jams only
when the printer is off. Otherwise, you may
damage the printer or change the top-of-form or
tear-off position.
4. Replace the printer cover and paper guide, and turn on the
printer. Make sure the Paper Out light is not flashing and
the Pause light is off.

Bidirectional Alignment

If you notice that the vertical lines in your printout are not
properly aligned, you can use the printer's bidirectional
adjustment mode to correct this problem.
To complete the steps below, you need 5 letter or A-4
size single sheets or 5 pages of continuous paper. If
you use single sheets, you need to load a new sheet of
paper each time the printer ejects a printed sheet onto
the paper guide.
1. Make sure paper is loaded and the printer is turned off.
Whenever you turn off the printer, wait at least 5
seconds before turning it back on; otherwise you
may damage the printer.
2. While holding down the
It enters the bidirectional adjustment mode, then prints
instructions and the first set of alignment patterns.
3. As described in the instructions, compare the alignment
patterns and select the pattern with the best alignment.
4. Follow the instructions to print the remaining sets of
alignment patterns and select the pattern with the best
alignment in each set.
5. After you select the best pattern in the final set of alignment
patterns, turn off the printer and exit the bidirectional
adjustment mode. Your selections are saved automatically.
button, turn on the printer.
Pause

Printing a Self Test

If you are having printing problems, you can run the printer's
self test to help you determine whether the printer or the
computer is causing the problem. If the self test results are
satisfactory, the printer is working properly and the problem
may be caused by your printer driver settings, application
settings, computer, or interface cable. (Be sure to use a shielded
interface cable.)
If the self test does not print properly, there is a problem with
the printer. See the Reference Guide for possible solutions to the
problem.
You can print the self test using either single sheets or
continuous paper. Use paper that is at least 8.25 inches
(210 mm) wide.
1. Make sure paper is loaded and the printer is turned off.
2. To run the test using a draft font, turn on the printer while
holding down the
printer's near letter-quality font, hold down the
button while you turn on the printer. (Either self test can
help you determine the source of your printing problem,
but the draft self test prints faster.)
After a few seconds, the printer begins printing the self test
(a series of characters).
To temporarily stop the self test, press the Pause
button. To resume, press it again.
3.To end the self test, press the
to stop printing. If paper remains in the printer, press the
button to eject the printed page. Then turn off the
LF/FF
printer.
Do not turn off the printer while it is printing the self
test. Always press the Pause button to stop printing
and the LF/FF button to eject the printed page before
you turn off the printer.

Cleaning the Printer

To keep your printer operating at its best, you should clean it
thoroughly several times a year. Follow these steps:
1. Remove any paper loaded in the printer and turn it off.
2. Unplug the power cord from the electrical outlet; then
disconnect the interface cable from the printer.
3. Remove the paper guide. If a pull tractor or an optional cut-
sheet feeder is installed, remove it.
4. Use a soft brush to carefully brush away all dust and dirt
from the outer case and paper guide.
7/06
Epson LX-300+II
button. To run the test using the
LF/FF
Pause
Epson LX-300+II
Load/Eject
button
15
-