CREE LIGHTING TRVMD Installationsanleitung Handbuch

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Außenleuchte CREE LIGHTING TRVMD herunter. CREE LIGHTING TRVMD 19 Seiten. Nom led street and area light

Seite drucken

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be

followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l'alimentation avant l'installation.

This luminaire must be installed in accordance with the NEC or your local

electrical code. If you are not familiar with these codes and requirements,

consult a qualified electrician.

Ce produit doit être installé conformément à NEC ou votre code électrique

local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez

contacter un électricien qualifié.

If NEMA

photo control is installed refer to NEMA

instructions.

If mounting bolts are completely removed in the field they should be hand

threaded (prior to use of power tools) to ensure proper engagement of the

thread when re-installing. Failure to pre-start threads may result in

cross-threading or stripping of the bolts during reinstallation.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE

TO INSTALL:

Mounting

Adjustment

Bracket

Steps

Mounting Bracket Bolts

LUMINAIRE INSTALLATION

STEP 1:

Slide fixture on to a minimum 8" long tenon,

through opening on the rear of housing. See

Figure 1.

STEP 2:

Once desired position is achieved, open cover

by holding fixture and loosen the captive

D-ring and allow the cover to swing open. See

Figure 2 and 3.

NOTE Maximum assembly torque value for

D-ring installation is 45 in-lbs (5 N·m).

1 of 7

Receptacle section for

D-ring

STEP 3:

To level fixture, use bubble level located

inside housing. Adjust leveling of fixture from

side to side by rotating fixture on tenon. To

level from front to back, slide pole in or out

to different step in upper housing. Each step

changes the angle in 2.5° increments

STEP 4:

NOTE: When tightening bolts make sure

to alternate between bolts to keep bracket

straight.

Traveyo Series

NOM LED Street and Area Light

Includes: TRVSM, TRVMD, TRVLG and TRVXL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D'INSTALLATION

• Prior to installation, store luminaire in a dry location

protected from rain, dust, and outdoor environment.

If equipped with a photocell receptacle, do not store

or install luminaire outdoors without immediately

installing a suitable photocell, shorting cap, or other

compatible device. Do NOT leave receptacle open to

environmental elements. Luminaires with a top-

mounted photocell receptacle should not be installed in

an up-light position or at a tilt greater than 45 degrees

from the down-light position.

• This product must be installed in accordance with the

applicable installation code by a person familiar with

the construction and operation of the product and the

hazards involved.

Importer: IDEAL PRODUCTS DISTRIBUTION DE MEXICO S.

DE R.L. DE C.V.

Address: Paseo de los Adobes, 1079, no. 10, Colonia

Guadalajara Technology Park, C.P. 45010

NOTE: TRVLG and TRVXL luminaires ordered

with 4BLT option will have (2) mounting

brackets and (4) mounting bolts.

Tighten mounting bolts to the appropriate

torque values specified in TORQUE VALUES

table on page 2. See Figure 1 (use 9/16"

socket wrench).

STEP 5:

Reference Electrical Connections section for

completing electrical connections.

LPN00620X0002A1_B