ARCHITETTURA SONORA CUBE400 Service-Handbuch - Seite 3
Blättern Sie online oder laden Sie pdf Service-Handbuch für Redner ARCHITETTURA SONORA CUBE400 herunter. ARCHITETTURA SONORA CUBE400 6 Seiten.
Seite drucken
3 >
Insert the perimeter acoustic dumper
inside the cube, making sure to reinsert it
behind the port tubes of the Cube, then
insert the rst acoustic dumper ring.
Place the crossover box "candy", complete
with cables, inside the Cube, positioning it
resting at in the bottom as shown in the
image. Be sure to place it with the 4-wire
cable facing up. Place the second sound-ab-
sorbing circular cap on top of it.
4 >
Slip the bipolar cable into the slot
under the
ange and through the
appropriate groove carved into the
Cube's body and pull the cable outsi-
de. Seal the cable into the groove with
silicone.
6 >
Overturn the coaxial on the
internal ange, matching the holes
in the basket with the holes in the
inner ange. Position the loudspe-
aker protection frame, paying
attention to an extreme coincide
with the holes of the speaker.
Using the Allen key #3 (B) turn the
four M5 screws counter-clockwise
until you hear a click that indicates
the correct insertion of the
thread of the screw in the threa-
ded seat. Then tighten the screws
by turning clockwise crosswise
(always tighten the screw opposite
to the previous one) until you start
feeling resistance.
8 >
Tighten the four screws M10
(always crosswise) with the torque
wrench #7(E) set at 12 N.m.
Then insert the thermo-shrinking
sheath, about 40 mm long, along the
cable where it comes out from the
base and heat it with the hot air gun
(G) at a temperature about 280°C.
WARNING:
do
not
recommended temperature in order
to prevent the fusion of the cable.
bipolar
cable
groove for
cable on body
second acoustic
dumper ring
rst acoustic
dumper ring
M10
screw (H)
rst
exceed
the
5 >
Place the coaxial over the inner
ange, overturned with the connectors
visible and insert the silicone gasket over
the coaxial basket. Stagnate the connec-
tors and the quadripolar cable and then
weld the contacts (welder temperature
400°C) on the coaxial, quickly enough to
avoid thermal damage to wires and internal
connections of the driver. Be sure to
remember the colors of the phases. (Brown
> +Woofer; Green > -Woofer; Yellow >
+Tweeter; White > -Tweeter)
7 >
Insert the cable in the through
Grower
column of the base and at the same time
washer (I)
place the base on the Cube taking extre-
Flat steel
washer (L)
me care not to scratch the frame below.
Red ber
IMPORTANT: the cable was previously
washer (M)
laid into the appropriate groove present
on the Cube's body and sealed with
silicone.
Place the 4 M10 screws (H), the
"Grower" (L), the at stainless steel and
the red ber washers in the holes of the
base with the red one in contact with the
base then the
"grower" and nally the screw.
Using the Allen key #7 (B) turn the four
M5 screws counter-clockwise until you
hear a click that indicates the correct
insertion of the rst thread of the screw in
the threaded seat. Then tighten the
screws by turning clockwise crosswise
(always tighten the screw opposite to the
previous one) until you start feeling
resistance.
9 >
Turn the Cube upside-down
back on its base, following the
Instruction Manual directions.
quadripolar cable
perimeter
acoustic dumper
crossover box
at steel one, then