Accustat Independence ES-U Betriebsanleitung

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Thermostat Accustat Independence ES-U herunter. Accustat Independence ES-U 3 Seiten.

Seite drucken

Installation and Operating Instructions

ES-AH11

Environmentally Friendly

MERCURY FREE!!

Use ONLY ACCUSTAT®

Temperature Setpoints

Application:

The ACCUSTAT®

designed to operate 24VAC to 30VAC single stage heating and cooling

systems. This thermostat is MERCURY FREE!! The ACCUSTAT®

models utilize pre-set plug-in temperature setpoints to

activate the circuits. Room air temperature is measured by a micro-

processor and compared with the plug-in setpoint temperature. This

thermostat can operate in heat only, cool only or be off. The fan cycles

on/off with calls for heating or cooling or can be on continuously. The

thermostat has a locking cover to prevent tampering.

Operating Conditions:

The electronic mechanisms incorporated within this unit REQUIRE

operating conditions similar to other electronic devices intended for

INDOOR USE ONLY, such as would be acceptable for TV and similar

household appliances. Relative humidity must be less than 95% and

the atmosphere must be non-condensing. Air quality must be main-

tained, FREE of heavy dust or debris which may infiltrate the interior

of this device. Installation in any space which is unfinished or under-

going repainting or general rehabilitation is also considered product

abuse. This device should be removed from service during any local

construction activity.

Cleaning:

This device incorporates a high impact styrene enclosure which is

easily cleaned with a dry cloth or vacuum brush. Occasional soiling

may be cleaned with a soft cloth lightly dampened with water and/or

mild cleaning solution. IN NO CASE should this device be directly

sprayed with or exposed to free flowing liquids, including water, which

could penetrate its interior.

FAILURE TO OBSERVE ANY OF THE ABOVE CONDITIONS OF USE

WILL COMPLETELY VOID THE SUPPLIER WARRANTY.

CAUTION

MAKE SURE UNIT IS PROPERLY CONNECTED. DAMAGE TO THE

CONTROL CAN BE CAUSED BY MISWIRING, WHICH WILL VOID

THE WARRANTY.

FAN

ON AUTO

ACCUSTAT

HEAT OFF COOL

model ES-AH11 thermostat was

Specifications:

Set Temperature Range: Determined by plug-in setpoint

Plug-in Setpoint Accuracy: ± 0.5°

Control Accuracy: ± 1.0°

Sampling Rate: Every 30 seconds

System: Switch selectable, heat only, cool only or off

Stages: Single stage heating/cooling

Differential: Switch selectable, 0.5° or 1.0°

Fan: Switch selectable, auto cycle or continuously on

Operating Temperature: 14°F to 105°F

Storage Temperature: -4°F to 105°F

Input: 20VAC to 32VAC

Load Rating: 1 amp maximum per circuit, 80mA minimum for

energy harvesting

Cycle Rate: 6 cycles per hour

Common Wire: Optional

Delay: 5 minutes on start-up

Energy Harvesting: Switch selectable, on or off

Enable switch if not connecting a common wire

Disable switch for sensitive loads, common wire will then be required

Thermostat Charge: Thermostat will hold its charge 3.5 hours during

a power failure

Enclosure: High impact styrene, white

Case can be locked, key required

TO OPEN:

1. Align key with slot and insert all the way

2. Locking pin will emerge. Pull out completely

3. Gently squeeze left side of cover to

release catches

4. Let right side work as a hinge

Swing cover out and remove

Squeeze

Insert

TO CLOSE: (Reverse Procedure)

1. Hinge right side of cover and close it

2. Gently squeeze left side of cover and

snap shut

3. Orient the locking pin as shown and

slide in until end is below surface of

cover (audible snap is heard when

pin is properly seated)

ATTENTION: This product does not contain mercury.

This product may be replacing a product containing

mercury.

Do not place the old product in the household trash.

For more information on recycling and proper disposal

visit TRC's website www.thermostat-recycle.org

Should a tube break, do not touch any spilled mercury.

Wear non-absorbent gloves, collect any spilled mercury

and place it in a sealed container. Contact your local waste

management authority for recycling and proper disposal

instructions.

Lift and

Rotate

Remove