Sharp Carousel R-1600 Service-Handbuch - Seite 30

Blättern Sie online oder laden Sie pdf Service-Handbuch für Mikrowellenherd Sharp Carousel R-1600 herunter. Sharp Carousel R-1600 48 Seiten. Over the range microwave oven
Auch für Sharp Carousel R-1600: Betriebshandbuch (28 seiten)

Seite drucken

R-1600

R-1601

R-1602

7. Remove one (1) screw holding the hood duct to the oven

cavity front plate.

8. Release the 6-pin connector and the 3-pin connector of

the main harness A from the hood duct.

9. Disconnect the wire leads from the fan motor and chassis

support, and release the wire leads from holes of the

hood duct.

10.Remove the two (2) unit mounting screws from the

chassis support (right side) and the hood duct (left side).

11.Remove the one (1) screw holding the chassis support.

12.Remove the chassis support.

13.Remove the hood duct from the oven cavity by lifting it up

14.Screw the oven lamp off from the lamp socket.

15.Remove the lamp socket from the lamp angle.

1. Disconnect the power supply cord , remove the oven

from wall and remove outer case (Refer to procedure of

"Removal of Oven from Wall" and "Outer case Removal".)

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from the fan motor and the

chassis support, and release them from the holes of

hood duct.

5. Remove the one (1) screw holding the hood duct to the

oven cavity front plate, and lift up the fan motor side of the

hood duct.

6. Remove the one (1) screw holding the capacitor holder to

the hood intake duct.

7. Disconnect the high voltage wire leads of the high

voltage rectifier assembly from the magnetron.

8. Disconnect the filament lead of the transformer from the

magnetron.

HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL

1. Disconnect the power supply cord , remove the oven

from wall and remove outer case (Refer to procedure of

"Removal of Oven from Wall" and "Outer case Removal".)

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from the fan motor and the

chassis support, and release them from the holes of

hood duct.

5. Remove the one (1) screw holding the hood duct to the

oven cavity front flange, and lift up the fan motor side of

the hood duct.

6. Disconnect the high voltage wire leads with high voltage

rectifier from the magnetron.

7. Disconnect filament lead of the transformer from high

1. Disconnect the power supply cord and remove the oven

from wall and remove outer case. (Refer to procedure of

"Removal of Oven from Wall" and "Outer case Removal")

2. Open the door and block it open.

3. Discharge high voltage capacitor.

4. Disconnect the wire leads from the hood fan thermal

MAGNETRON REMOVAL

HOOD FAN THERMAL CUT-OUT REMOVAL

16.Pull the wire leads from the oven lamp socket by pushing

the terminal hole of the oven lamp socket with the small

flat type screw driver.

17.Now, the oven lamp socket and the hood duct are free.

Terminal

Wire lead

9. Remove the power transformer from the right base plate,

referring to "POWER TRANSFORMER REMOVAL".

10.Carefully remove four (4) mounting screws holding the

magnetron to waveguide. When removing the screws

hold the magnetron to prevent it from falling.

11.Remove the magnetron from the unit with care so the

magnetron tube should not be hit by any metal object

around the tube.

12.Remove the one (1) screw holding the magnetron air

guide to the magnetron.

13.Remove the magnetron air guide

CAUTION: WHEN REPLACING THE MAGNETRON, BE

SURE THE R.F. GASKET IS IN PLACE AND

MOUNTING SCREWS ARE TIGHTENED SE-

CURELY.

voltage capacitor.

8. Disconnect high voltage wire from capacitor.

9. Remove one (1) screw holding capacitor holder and high

voltage rectifier to the hood intake duct.

10.Disconnect the high voltage rectifier assembly from the

high voltage capacitor.

11.Now, the high voltage rectifier assembly is free.

12.Remove capacitor from the holder.

13.Now, the high voltage capacitor is free.

CAUTION: WHEN REPLACING THE HIGH VOLTAGE

RECTIFIER ASSEMBLY, THE GROUND SIDE

TERMINAL MUST BE SECURED FIRMLY

WITH A GROUNDING SCREW.

cut-out.

5. Remove one (1) screw holding the thermal cut-out to the

right base plate.

6. Remove the hood fan thermal cut-out from the right base

plate.

7. Now, the hood fan thermal cut-out is free.

Oven lamp

socket

Terminal hole

Flate type small

screw driver