Sharp Carousel R-880FS Service-Handbuch - Seite 14

Blättern Sie online oder laden Sie pdf Service-Handbuch für Mikrowellenherd Sharp Carousel R-880FS herunter. Sharp Carousel R-880FS 48 Seiten. Double grill convection microwave oven
Auch für Sharp Carousel R-880FS: Service-Handbuch (3 seiten)

Seite drucken

R-880F(S)

PROCEDURE

LETTER

MAGNETRON TEST

NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL

WHILE THE OVEN IS IN OPERATION.

CARRY OUT 3D CHECKS.

Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal.

To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron

filament terminals, the meter should show a reading of less than 1 ohm.

To test for short filament to anode condition, connect ohmmeter between one of the filament terminals

and the case of the magnetron (ground). This test should be indicated an infinite resistance. If a low

or zero resistance reading is obtained then the magnetron should be replaced.

MICROWAVE OUTPUT POWER (1 litre load)

The following test procedure should be carried out with the microwave oven in a fully assembled

condition (outer case fitted). Microwave output power from the magnetron can be measured by IEC

Test Procedure, i.e. it is measured by how much power the water load can absorb. To measure the

microwave output power in the microwave oven, the relation of calorie and watt is used. When P(W)

heating works for t(second), approximately P x t/4.187 calorie is generated. On the other hand, if the

temperature of the water with V(ml) rises T ( C) during this microwave heating period, the calorie of

the water is V x T.

The formula is as follows;

P x t / 4.187 = V x

Our condition for water load is as follows:

Room temperature (T0) ... around 20 C

Water load .................................. 1000 g

Heating time .............................. 47 sec.

T2 ............................ Final Temperature

Measuring condition:

1. Container

The water container must be a cylindrical borosilicate glass vessel having a maximum material

thickness of 3 mm and an outside diameter of approximately 190 mm.

2. Temperature of the oven and vessel

The oven and the empty vessel are at ambient temperature prior to the start the test.

3. Temperature of the water

The initial temperature of the water is (10 1) C.

4. Select the initial and final water temperature so that the maximum difference between the final water

temperature and the ambient temperature is 5K.

5. Select stirring devices and measuring instruments in order to minimize addition or removal of heat.

6. The graduation of the thermometer must be scaled by 0.1 C at minimum and be an accurate

thermometer.

7. The water load must be (1000 5) g.

8. "t" is measured while the microwave generator is operating at full power. Magnetron filament heat-

up time is not included.

NOTE: The operation time of the microwave oven is "t + 3" sec. (3 sec. is magnetron filament heat-up time.)

Measuring method:

1. Measure the initial temperature of the water before the water is added to the vessel.

(Example: The initial temperature T1 = 11 C)

2. Add the 1 litre water to the vessel.

3. Place the load on the centre of the shelf.

4. Operate the microwave oven at HIGH for the temperature of the water rises by a value

(10

5. Stir the water to equalize temperature throughout the vessel.

6. Measure the final water temperature. (Example: The final temperature T2 = 21 C)

7. Calculate the microwave power output P in watts from above formula.

TEST PROCEDURES

T+ 0.55 x mc (T2-T0)

2) K.

COMPONENT TEST

P (W) = 4.187 x V x T / t + 0.55 x mc (T2-T0)/t

Power supply Voltage .............. Rated voltage

Initial temperature (T1) ...................... 10 1 C

Mass of container (mc) ......................... 330 g

P = 90 x T+ 0.55 x mc(T2-T0)/47

T of