Sharp CD-BA2100 Betriebshandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Betriebshandbuch für Stereo System Sharp CD-BA2100 herunter. Sharp CD-BA2100 18 Seiten. Sharp mini component system operation manual cd-ba2100
Auch für Sharp CD-BA2100: Kurzanleitung (2 seiten)
Seite drucken
PRECAUTIONS
General
Do not use oil, solvents, gasoline, paint thinners or insec-
ticides on the unit.
Do not expose the unit to moisture, to temperatures higher
than 140˚F (60˚C) or to extreme low temperatures.
Keep the unit away from direct sunlight, strong magnetic
fields, excessive dust, humidity and electronic/electrical
equipment (home computers, facsimiles, etc.) which
generates electrical noise.
Hold the AC power plug by the head when removing it
from the AC outlet, as pulling the cord can damage internal
wires.
When cleaning the heads, pinch rollers, etc, remove the
AC power plug from the AC outlet as the unit contains
high voltages.
Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local SHARP
service facility.
Use the unit on a firm, level surface free from vibration,
and do not place anything on the top of the unit.
If the unit does not work properly while in use, disconnect
the AC power cord from the AC outlet. Plug the AC power
cord back in, and then press the ON/STAND-BY button to
turn the power on.
If an electrical storm is taking place near you, it is sug-
gested that you disconnect the AC power cord from the
AC outlet for safety.
Warning:
The voltage used must be the same as that specified on this
unit. Using this product with a higher voltage other than which
is specified is dangerous and may result in a fire or other
type of accident causing damage. SHARP will not be held
responsible for any damage resulting from use of this unit
with a voltage other than that which is specified.
Volume control
The sound level at a given volume setting depends on a
combination of speaker efficiency, location and various other
factors.
It is advisable to avoid exposure to high volume levels, which
occur while turning the unit on with the volume control setting
up high, or while continually listening at high volumes.
Condensation
Sudden temperature changes, storage or operation in an ex-
tremely humid environment may cause condensation inside
the cabinet (CD pickup, tape heads, etc.) or on the transmit-
ter LED on the remote control.
Condensation can cause the unit to malfunction.
If this happens, leave the power on with no disc (or cassette)
in the unit until normal playback is possible (about 1 hour).
Wipe off any condensation on the transmitter LED with a soft
cloth before operating the unit.
Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface.
Follow the guidelines below for maximum enjoyment from
your CD collection and player.
Do not write on either side of the disc, particularly the
non-label side. Signals are read from the non-label side.
Do not mark this surface.
Keep your discs away from direct sunlight, heat, and ex-
cessive moisture.
Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the center, along the radius.
Cassette tape
For playback, use normal or low-noise tape for the best
sound. (Metal or CrO
For recording, use only normal tape.
Do not use C-120 tapes, tapes with large diameter reels,
or poor-quality tapes, as they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or pencil.
Cassettes have removable tabs which prevent accidental
recording or erasing from taking place. Removing the tab
will protect the corresponding side from being erased.
Cover the tab holes with adhesive tape to erase or record
again.
TAPE 1: Playback only.
TAPE 2: Playback or record.
Tab for side B (2)
2
tape is not recommended.)
2
Side A (1)
Tab for side A (1)
NO
YES
Correct