Sharp AR-M351N Handbuch für den Schlüsselbetrieb - Seite 14
Blättern Sie online oder laden Sie pdf Handbuch für den Schlüsselbetrieb für Alles in einem Drucker Sharp AR-M351N herunter. Sharp AR-M351N 20 Seiten. Digital printer
Auch für Sharp AR-M351N: Broschüre & Specs (7 seiten)
Seite drucken
GENERAL PROGRAMS
Saddle stitch position adjust
This program is used to adjust the stapling position
(folding position) when using the saddle stitch function
of the optional saddle stitch finisher.
The value can be adjusted in 0.1 mm increments within
±3.0 mm from the reference position for each paper size.
Max.+3mm
Position adjusted
to the plus
direction
1
2
Reference position
[AUTOMATIC SADDLE STITCH] checkmark
The saddle stitch print function can normally be divided
into the following three general steps.
1. The pages of the original are automatically
reordered to allow saddle stitch binding (saddle
stitch function).
2. The pages are folded at the centre.
3. The paper is stapled at the centre in two places
(saddle stitch stapling).
The [AUTOMATIC SADDLE STITCH] checkbox is
selected by default.
Selection of the checkbox assumes the use of the
above saddle stitch printing function (three steps).
Saddle stitch stapling exceptions
Depending on the purpose of saddle stitch stapling, it
may be necessary to perform saddle stitch stapling on
printed matter that has already been bound by saddle
stitching. In this case, it is necessary to disable step 1
above. If you frequently perform this type of
exceptional saddle stitch stapling that requires
disabling step 1, remove the checkmark from the
[AUTOMATIC SADDLE STITCH] checkbox.
High speed stacking
This program is used to have print speed priority, which
is available for printing in the offset mode with the
saddle stitch finisher.
When this program is on, slight decrease of stacking
performance might occur.
This program is set in the factory default setting.
Rotated output
When Rotated output is turned on, you can have the
paper output orientation (A4-size paper only) of each
set of copies alternate between horizontal and vertical.
This function is used to sort output when neither the
Finisher peripheral nor the Saddle stitch finisher
peripheral are installed.
* To use this function, A4-size paper must be loaded
both horizontally and vertically in the paper trays.
This function works when paper is output to the
centre tray.
12
Min.-3mm
Position adjusted
to the minus
direction
12
11
The function does not work in the following cases:
• When paper is output to the Finisher peripheral or the
Saddle stitch finisher.
• Printing in Group mode.
• When a letter-size original is printed on A4-size
paper using the "A4/letter size auto change" key
operator program (page 5-5 of the "Operation
manual (for printer)").
• When "Transparency Inserts" or "Different Paper
settings" is selected in the printer driver.
• When the "Paper Source" drop down in the "Paper
Selection" is set to any selection other than "Auto
Select" in the printer driver.
• When the printing paper size for a stored job or a job
in progress has been overridden and changed to A4
size.
NOTE
When interrupt copying is performed, Rotated output
does not take place to distinguish the output of
regular copying from interrupt copying. Also,
Rotated output cannot be used to sort output by job.
Auto paper selection setting
Use this program to select the paper type* for which the
automatic
paper
selection
Selections are "PLAIN PAPER", "PLAIN AND
RECYCLE PAPER", and "RECYCLE PAPER".
* The paper type set for each paper tray in the paper
tray settings of the user settings (page 2-5 of the
"Operation manual (for general information and
copier operation)").
Optimization of a hard disk
This is used to optimize the "Main folder" and "Custom
folder" that are used for the document filing function.
When this program is executed, a message will appear
asking if it is okay to stop the job in progress. Touch the
[YES] key to stop the job and begin optimization. When
optimization ends, the machine will restart if the power
switch is switched on, or turn off if the power switch is
switched off.
CAUTION
If the power switch is switched off or the power plug
is unplugged while optimization is in progress, the
hard drive may be damaged and stored data or
received data may be lost.
function
operates.