Shimano CB-E110 Dienstanweisungen

Blättern Sie online oder laden Sie pdf Dienstanweisungen für Zubehör für Fahrräder Shimano CB-E110 herunter. Shimano CB-E110 1 Seiten. Coaster brake e-type

Seite drucken

General Safety Information

WARNING

– To avoid serious injuries:

It is important to completely understand the operation of

your bicycle's brake system. Improper use of your bicycle's

brake system may result in a loss of control or an accident,

which could lead to sever injury. Because each bicycle

may handle differently, be sure to learn the proper braking

technique (including bicycle control characteristics) and

operation of your bicycle. This can be done by consulting

your professional bicycle dealer and the bicycle owner's

manual, and by practicing your riding and braking

technique.

When securing the brake arm to the frame, be sure to use

a brake arm clip that matches the size of the chainstay,

and securely tighten them with the clip screw and clip nut

to the specified tightening torque.

Use a lock nut with a nylon insert (self-locking nut) for the

clip nut. It is recommended that standard Shimano parts be

used for the clip screw, clip nut and brake arm clip. In

addition, use a brake arm clip that matches the size of the

chainstay.

If the clip nut comes off the brake arm, or if the clip screw

or brake arm clip becomes damaged, the brake arm may

rotate on the chainstay and cause the handlebars to jerk

suddenly, or the bicycle wheel may lock and the bicycle

may fall over, causing serious injury.

Obtain and read the service instructions carefully prior to

installing the parts. Loose, worn, or damaged parts may

cause serious injury to the rider.

We strongly recommend only using genuine Shimano

replacement parts.

Check that the wheels are fastened securely before riding

the bicycle. If the wheels are loose in any way, they may

come off the bicycle and serious injury may result.

Read these Technical Service Instructions carefully, and

keep them in a safe place for later reference.

CAUTION

– To avoid serious injuries:

Spin the wheel and confirm that the braking force of the

coaster brake is correct.

If the brakes are used frequently, the hub shell may

become hot. Do not touch the hub shell for at least 30

minutes after you finish riding the bicycle.

Hub shell

NOTE:

The CB-E110 should be used with Sprockets from 15T

to 23T.

If the wheel becomes stiff and difficult to turn, you

should lubricate it with grease.

Do not apply any lubricant to the inside of the hub,

otherwise the grease will come out.

You should periodically wash the sprockets in a neutral

detergent and then lubricate them again. In addition,

cleaning the chain with neutral detergent and

lubricating it can be a effective way of extending the

useful life of the sprockets and the chain.

If the chain keeps coming off the sprockets during use,

replace the sprockets and the chain.

Parts are not guaranteed against natural wear or

deterioration resulting from normal use.

For maximum performance we highly recommend

Shimano lubricants and maintenance products.

For any questions regarding methods of handling or

adjustment, please contact the place of purchase.

CB-E110

Coaster Brake

E-type

Technical Service Instructions

Installation of the sprocket to the

hub

Place the dust cap onto the driver on the right side of the

hub body. Next, install the Sprocket and secure it in place

with the snap ring.

Snap ring

Sprocket

Note the

direction

Dust cap

Driver

Note:

Check that the snap ring is sitting securely in the

groove of the hub body.

Groove of

hub body

Snap ring

Installation of the hub to the frame

Mount the chain on the sprocket, and then set the hub

axle into the fork ends.

Attach the brake arm to the chainstay with the brake

arm clip, and then lightly tighten the clip screw and clip

SI-2860A

nut to provisionally secure the brake arm in place.

Clip nut

Brake arm

Screw the flange nuts or the toothed washers and hub

nuts onto both ends of the Hub axle. After this, take up

the slack in the chain and then tighten the flange nuts

or hub nuts to secure the wheel to the frame.

Tightening torque:

30 – 45 N·m

{260 – 390 in. lbs.}

Flange nut or toothed washer and hub nut

Flange nut

Toothed washer

Note:

Check that the right end of the Hub axle protrudes

from the edge of the flange nut or hub nut by at

Sprocket

least 2 mm.

Sprocket

Overall dimensions of fork end,

stand and mudguard stay

(Varies depending on the bicycle)

Fix the brake arm securely to the chainstay with the

Hub axle

brake arm clip.

Fork end

Note:

When installing the brake arm clip, securely

tighten the clip screw while holding the clip nut

with a 10 mm spanner.

Tightening torque:

2 – 3 N·m {17 – 26 in. lbs.}

After installing the brake arm clip, check that the

clip screw protrudes about 2 – 3 mm from the

surface of the clip nut.

Clip screw

Clip nut

Brake arm clip

2 – 3 mm

Chainstay

Before using the Coaster Brake, check that the brake

works properly and that the wheel turns smoothly.

These service instructions explain how to use and maintain

the Shimano bicycle parts which have been used on your

new bicycle. For any questions regarding your bicycle or

other matters which are not related to Shimano parts‚ please

contact the place of purchase or the bicycle manufacturer.

These service instructions are printed on recycled paper.

Please note: Specifications are subject to change for improvement without

notice. (English)

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

Hub nut

3-77 Oimatsu-cho, Sakai, Osaka 590-8577, Japan

Thread should

be visible

Hub axle

Flange nut

Fork end

Brake arm

Brake arm clip

Clip screw

(M6

16 mm)

Mar. 2004 by Shimano Inc. PIT. SZK. Printed in Japan