Crestron DigitalMedia 8G+ DM-TX-4K-100-C-1G-B-T Aus dem Handbuch
Blättern Sie online oder laden Sie pdf Aus dem Handbuch für Transmitter Crestron DigitalMedia 8G+ DM-TX-4K-100-C-1G-B-T herunter. Crestron DigitalMedia 8G+ DM-TX-4K-100-C-1G-B-T 2 Seiten. Wall plate 4k transmitter
Seite drucken
DO
GUIDE
DM-TX-4K-100-C-1G
Wall Plate 4K DigitalMedia 8G+
DO
Make Connections to the Rear Panel
Make connections to the rear panel of the DM-TX-4K-100-C-1G before mounting the unit into an
electrical box. If the unit is to be mounted under a table or onto a at surface or rack rail, make
connections to the rear panel after the unit is mounted. (For mounting instructions, refer to the
"DO Install the Device" section in this guide.)
Make connections to the rear panel as follows:
DM OUT: Connect to the DM 8G+
®
input of a DigitalMedia™ switcher, DigitalMedia 8G+
receiver, or other DigitalMedia device or to an HDBaseT
NOTE:
The DM OUT port is a PoDM (Power over DM) and PoH (Power over HDBaseT) PD
(Powered Device) port. To receive PoDM or PoH, the DM-TX-4K-100-C-1G requires a connection
to a DigitalMedia switcher or other equipment that has a PoDM or PoH PSE (Power Sourcing
Equipment) port. Any wiring that is connected to a PoDM or PoH PSE port is for intrabuilding
use only and should not be connected to a line that runs outside of the building in which the
PSE is located.
24VDC 0.75A: Connect to the included power pack using the included 2-pin interface
connector.
NOTE:
Connection to the power pack is not required when PoDM or PoH is used to power the
device.
G: Connect to earth ground (building steel).
Refer to illustrations and for sample rear panel connections.
Connection to DigitalMedia Switcher Using PoDM
(External Power Pack Not Required)
Ground
DM-MD8X8
Transmitter 100
®
device.
®
Connection to DigitalMedia Receiver
(External Power Pack Required)
Ground
DM
IN
RES
ET
I OUT
0 -
C
UP
HDM
1 0
SET
- 4
K -
ER
M C
RO
LL
D M
- R
NT
CO
RO
OM
24
A MAX
V
GND
COM
DM
0.75
RX
TX
RTS
DB
T
TM
CTS
A SE
S
1
IR
S
G
2
G
LAN
DM-RMC-4K-100-C
DO
Check the Box
QTY PRODUCT
1
Bracket (for Interface Module)
2
Connector, 2-Pin
1
Connector, 3-Pin
1
Power Pack, 24 Vdc 0.75 A, 100-240 Vac
2
Screw, 6-32 x 3/4", Truss Head, Combo
2
Screw, 6-32 x 1/4", Pan Head, SEMS
Not Included: Electrical Box, Philips Head Screwdriver, Decorator-Style Faceplate and Screws, Cables, Rack Mount Screws, and Table or Surface
Mount Screws
DO
Install the Device
®
The DM-TX-4K-100-C-1G can be mounted into an electrical box, under a table, or onto a at
surface or rack rail.
Mounting into an Electrical Box
The DM-TX-4K-100-C-1G mounts into a 1-gang electrical box (not included). A minimum
mounting depth of 3-1/2 inches (89 mm) is required.
Using a Phillips head screwdriver, attach the DM-TX-4K-100-C-1G to the electrical box using
the two included 6-32 x 3/4-inch truss combo head screws. Then, attach a decorator-style
faceplate (not included) to the front panel of the DM-TX-4K-100-C-1G using two screws (not
included). Refer to illustration .
Mounting into an Electrical Box
Power
Pack
COLOR
PART NUM.
Black
2016054
2003574
2003575
2037285
2009211
Black
2007218