Epson 7800p - PowerLite XGA LCD Projector Produktinformation Handbuch - Seite 14

Blättern Sie online oder laden Sie pdf Produktinformation Handbuch für Projektor Epson 7800p - PowerLite XGA LCD Projector herunter. Epson 7800p - PowerLite XGA LCD Projector 22 Seiten. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Auch für Epson 7800p - PowerLite XGA LCD Projector: Benutzerhandbuch (42 seiten), Betriebshandbuch (36 seiten), Schnelles Einrichten (2 seiten), Ersatzteile (1 seiten), Betriebshandbuch (47 seiten), Installationshandbuch (5 seiten), Spezifikationsblatt (2 seiten), Technischer Brief (7 seiten), Produkt-Support-Bulletin (25 seiten), Produkt-Support-Bulletin (22 seiten), Produkt-Support-Bulletin (28 seiten), Produkt-Support-Bulletin (41 seiten), Produkt-Support-Bulletin (15 seiten), Produkt-Support-Bulletin (22 seiten)

Seite drucken
Epson 7800p - PowerLite XGA LCD Projector Produktinformation Handbuch
Managing Projectors from a Remote
Computer
The EasyManagement software lets you monitor and control
projector(s) from a remote computer. These features are
intended for use by network administrators.
Use EMP Monitor to see your projectors' status, switch
image sources, and control basic settings.
Use EMP NetworkManager to receive e-mail notifications
alerting you to possible problems.
Use a network management utility running SNMP, such as
™
HP OpenView,
to manage your facility's equipment from
a pre-existing system.
Note: A plug-in is available to allow you to manage your
projectors in HP OpenView. Additionally, other SNMP
management utilities may be available in the future. Check with
EPSON for availability.
Make sure you have installed the software (included on the
projector's CD-ROM) on the computer you want to use to
monitor your projectors. (See the User's Guide for
instructions.)

Setting Up the Network

Connect each projector you want to monitor to your network
and configure it with an appropriate IP address.
1. Connect the projector to your network using a
commercially available 100baseTX or 10baseT network
cable. Plug the cable into the projector's Ethernet port.
Ethernet port
To network port
2. Turn on the projector.
EPSON PowerLite 7800p Projector
3. Press the
button on the remote control and select
Menu
from the
Network
Video
Br Brightness Control
Audio
Projector ID
Projector ID
Effect
Netw
Network
Setting
COM P
COM Port
User's Logo
Auto setup
uto setup
Advanced1
BNC Sync Ter ermination
BNC Sync
Advanced2
Reset
Reset
About
Reset All
[
]: Select
[
]: Enter
4. If your network assigns addresses automatically, turn on
.
DHCP
5. If your network does not assign addresses automatically,
turn off
and enter the projector's
DHCP
, and
Subnet Mask
To enter numbers using the remote control, press the
button until it lights, then use the numeric
Num
keypad.
Num button
To change the network addresses from the projector's
control panel, press the right and left arrow buttons to
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
Select the part of the
address to change
Note: If you're a network administrator, you can use the
option to enter a trap IP address. This lets you receive
SNMP
trap alerts for the projectors you're monitoring. If you have
HP OpenView, a plug-in is available to allow you to manage
your projectors in HP OpenView. Check with your dealer or
EPSON.
5/03
EPSON PowerLite 7800p Projector
menu.
Advanced2
:
ightness Control
High
High
Low
: 1
Set
Set
Set
Set
:
RS-232C
RS-232C
USB
USB
:
ON
ON OFF
OFF
:
mination
ON OFF
ON
OFF
Execute
Ex
ecute
[Menu]: Exit
IP Address
, as needed.
Gateway Address
Zero
Select
Network
,
Increase or
decrease
the value
13
-