4. Hold down the
button
Num
on the remote control and use
the numeric keypad to enter a
4-digit password.
The password will be
displayed as
. After you
****
enter the last digit, a
confirmation screen appears.
Enter the password again.
5. After you finish setting the
password, press the
ESC
button to return to the
Password Protect menu.
6. Press the
button to deactivate the numeric keypad.
Num
Make a note of the password and keep it in a safe place in case
you forget it.
Creating a User's Logo
You can transfer any image on your computer to the projector,
and then use it as the startup screen and/or the screen that is
displayed when you press the
can be a company logo, slogan, photograph, or any other
image you want to use.
Follow these steps to capture the image and transfer it to the
projector:
1. Display the image you want to use on the projector. You
can use an image from either a computer or video source,
such as a VCR.
2. Press the
button and select the
Menu
3. Press
to select
Enter
Execute
Note: If the
User's Logo Protect
message that the logo cannot be recorded. You'll need to
disable
User's Logo Protect
the logo. See the next section, "Turning On the Password and
User's Logo."
4. When you see a message asking if you want to use the
present image as a user's logo, select
selection box displays over the image.
5. Use the
pointer button on the remote control to select
the area of the image you want to use. Once you've selected
the area, press
.
Enter
6. When you see the message
and press
. If you want to change the area selected,
Enter
select
, press
, and repeat steps 4 through 6.
No
Enter
Num button
Numeric keypad
button. The image
A/V Mute
menu.
User's Logo
.
option is
, you see a
ON
before you can create or change
and press
Yes
Enter
, choose
Select this image?
7. When you see this screen, select a zoom rate (display size),
and then press
8. When you see the message
select
and press
Yes
seconds. Do not use the projector or other sources
(computer, video, etc.) while the logo is being saved.
9. When you see the message
Turning On the Password and User's Logo
To enable the password and User's Logo, follow these steps:
1. Press the
Freeze
seconds until you see the Password Protect menu.
2. Select
Power ON Protect
3. Select
ON and
4. If you want to disable the password temporarily, select
and press
Timer
while you use the numeric keypad to enter the number of
hours (from 0 to 9999) you want the password feature
disabled. If you want the projector to request the password
every time it is turned on, set the timer to
The timer starts counting as soon as you close the Password
Protect menu. (You can check the elapsed time in this menu
next to
Time elapsed
When the period defined in the Time-elapsed setting has
passed, and the password is entered correctly, the elapsed
time will be reset to
Remember to disable or change this setting when you're
finished using it.
. A
5. To enable your User's Logo, select
press
. Then select
Enter
When this feature is on, the logo appears whenever the
projector is turned on (if the
in the Setting menu) and as the A/V Mute screen (if you
Yes
selected
Logo
Note: None of the User's Logo features can be changed when the
User's Logo Protect function is enabled.
6. Press
Menu
7. Turn off the projector and unplug the power cord to enable
password protection.
9/04
Epson PowerLite 7900p Projector
.
Enter
User's Logo
Set the zoom rate.
Zoom rate:
Zoom rate:
100% 200% 300%
Save image as user's logo?
. Saving the logo takes about 15
Enter
Completed
button on the remote control for about 5
and press
Enter
press
.
ESC
. Then hold down the
Enter
.)
and the timer will start again.
0H
User's Logo Protect
and press
ON
Enter
No-Signal Msg
as the
setting in the Setting menu).
A/V Mute
to close the Password Protect menu.
Epson PowerLite 7900p Projector
,
, press
.
ESC
.
button
Num
.
0H
and
.
is set to
Logo
13
-
Seite drucken