Epson 8100i - PowerLite XGA LCD Projector Produktinformation Handbuch - Seite 8
Blättern Sie online oder laden Sie pdf Produktinformation Handbuch für Projektor Epson 8100i - PowerLite XGA LCD Projector herunter. Epson 8100i - PowerLite XGA LCD Projector 13 Seiten. Product support bulletin(s)
Auch für Epson 8100i - PowerLite XGA LCD Projector: Handbuch Kommunikation (20 seiten), Benutzerhandbuch (1 seiten), Spezifikationsblatt (2 seiten), Technischer Brief (7 seiten), Produkt-Support-Bulletin (1 seiten)
Seite drucken
EPSON PowerLite 8100i/9100i Projector
Resizing the Image
If only part of your computer screen is displayed, your
computer may be set for a higher resolution than the
projector's "native" display: 1024
8100i) or 1280
1024 (PowerLite 9100i). You can resize the
image to fit the resolution of your projector.
Press the
button on the remote control or the control
Resize
panel. The screen image is automatically compressed.
Continue pressing the
Resize
screen in the original resolution.
If you're projecting from video equipment, pressing the
button switches the aspect ratio between 4:3 and 16:9.
Resize
If you have zoomed in on your image, you can also use the
button to switch it back to the original display size.
Resize
Note: You can also resize your image with the
when you're projecting from a VCR or other video source.
Projector Status Lights
The lights on top of the projector indicate the projector's
operating status.
Light
Status
Description and action
Orange
The projector is in sleep mode. You can
unplug it to turn it off, or press the Power
button to turn it on.
Flashing
The projector is warming up. Wait for the
green
image to appear.
Green
The projector is operating normally.
Flashing
The projector lamp is off and the projector is
orange
cooling down. You can't turn the projector on
or unplug it when the light is flashing.
Red
Power is cut off because of an internal
problem. Contact EPSON for help.
8 - EPSON PowerLite 8100i/9100i
768 pixels (PowerLite
button to pan around the
button
Resize
power light
lamp light
temperature light
Light
Status
Flashing
orange
Flashing red
Flashing
orange
Red
Flashing red
Using the Remote Control
The remote control uses a line-of-sight infrared signal. It lets
you access the projector's features from anywhere in the
room—up to 32 feet away. (This distance may be shorter if
the remote control batteries are low.) You must also be within
a ±30° angle from the front or rear receiver. If you have
connected the mouse cable, you can also use the remote
control as a wireless mouse.
The projector may not respond to remote control commands
in these conditions:
You are too far away or not within 30 to the left or right of
and 15 above or below the front or rear sensor
The
(remote control) switch is in the
R/C
Batteries are weak
Ambient light is too bright
A fluorescent light is shining into the infrared receiver
A strong light source (such as direct sunlight) shines into the
infrared receiver
Other equipment emitting infrared energy is present (such as
a radiant room heater)
The remote control buttons are shown in the following
illustrations.
3/01
Description and action
The lamp is almost burned out. This is a good
time to replace it.
The lamp is burned out (or defective) or there
is a problem with the ballast power.
The projector is too hot. Turn it off and let it
cool before using it.
The projector has turned off automatically
because it has overheated. Let it cool for a few
minutes, then turn it back on. Make sure there
is plenty of space around and under the
projector for ventilation. If it continues to
overheat, you may need to change the air
filter.
There is a problem with the cooling fan or
temperature sensor. Turn off the projector and
unplug it. Contact EPSON for help.
OFF
position