Siemens Washing machine Gebrauchsanweisung - Seite 2
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Waschmaschine Siemens Washing machine herunter. Siemens Washing machine 10 Seiten. Washing machine
Auch für Siemens Washing machine: Handbuch für Installation und Wartung (10 seiten), Betriebsanleitung (8 seiten), Installationsanleitung Handbuch (6 seiten), Gebrauchsanweisung und Installationsanleitung (28 seiten), Kurzreferenz-Anleitung (2 seiten), Kurzreferenz-Anleitung (2 seiten), Kurzreferenz-Anleitung (2 seiten), Gebrauchsanweisung und Installationsanleitung (28 seiten), Gebrauchsanweisung (28 seiten), Installationsanleitung Handbuch (6 seiten), Betriebsanleitung (10 seiten), Kurzreferenz-Anleitung (2 seiten), Gebrauchsanweisung (10 seiten), Gebrauchsanweisung Handbuch (28 seiten)
Seite drucken
Safety instructions
Important information
– Read the Instruction manual and Installation instructions and all other information enclosed with the washing
Before washing for the first time
machine and act accordingly.
Do not put any laundry in the machine. Turn the tap on. Pour into compartment II:
– Retain the documents for subsequent use.
– approx. 1 litre water
Risk of electric shock
– Never pull the cable to disconnect the mains plug
– detergent (dosage according to the manufacturer's instructions for light soiling and according to water hardness)
– Only insert/pull out the mains plug with dry hands.
Set the programme selector to Easy-Care 60 °C and press Start/Reload. At the end of the programme,
turn the programme selector to Off.
Danger to life
For appliances that have reached the end of their service life:
Protecting the laundry and the machine
– Disconnect the mains plug.
– Empty pockets.
– Sever the mains cable and discard along with the plug.
– Look out for metal items (paperclips, etc.).
– Destroy the lock on the washing machine door. This will prevent children from
– Wash delicates in a laundry bag (tights, curtains, underwired bras).
locking themselves in and risking their lives.
– Fasten zips, do up any buttons.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of children.
– Brush sand out of pockets and collars.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
– Remove curtain fittings or place in the laundry bag.
Loading laundry
Risk of explosion
– Items of laundry pretreated with cleaning agents containing solvents, e.g. stain
remover/cleaning solvent may cause an explosion after being loaded into the
– For optimum spin behaviour, load large and small items of laundry together.
washing machine.
– Individual items may lead to considerable imbalances.
Rinse items of laundry thoroughly by hand beforehand.
– Take care not to trap items of laundry between the washing machine door and the rubber seal.
Risk of injury
– The washing machine door can become very hot.
Soaking
Load laundry of the same colour.
– Be careful when draining hot detergent solution.
Pour detergent into compartment II in accordance with the manufacturer's instructions. Set the programme selector to
– Do not climb onto the washing machine.
Cottons/Coloureds 30 °C and press Start/Reload. After approx. 10 minutes, press Start/Reload to stop the pro-
– Do not lean on the open washing machine door.
gramme. Once the required soaking time has elapsed, press Start/Reload again to continue the programme,
– Do not reach into the drum if it is still rotating.
or select a different programme.
Starching
Laundry must not be treated with fabric softener
Consumption values
Starching is possible in all wash programmes if liquid starch is used. Pour starch into the
compartment in accordance with the manufacturer's instructions (rinse first if necessary).
Electricity
Programme
Programme
Option
Load
Water***
Dyeing / bleaching
consumption***
duration***
Dye should only be used in normal household quantities. Salt may damage stainless steel. Always follow the dye
Cottons/Coloureds 30 °C**
8 kg
0.35 kWh
57 l
2:06 h
manufacturer's instructions. Do not use the washing machine for bleaching clothes.
Cottons/Coloureds 40 °C**
8 kg
0.97 kWh
57 l
2:16 h
Load display
Cottons/Coloureds 60 °C**
8 kg
1.36 kWh
57 l
2:26 h
The load sensor detects how heavily the washing machine is loaded. The laundry is not weighed.
Cottons/Coloureds 60 °C
ecoPerfect*
8 kg
0.87 kWh
57 l
4:00 h
Recommended dosage
Cottons/Coloureds 90 °C
8 kg
2.34 kWh
68 l
2:16 h
Based on the selected programme and the detected load, the recommended dosage function provides a recommen-
Mixed Fabrics 40 °C**
3.5 kg
0.47 kWh
37 l
0:53 h
dation for the detergent dosage in %. The % figure refers to the recommendation of the detergent manufacturer.
Easy-Care 40 °C**
3.5 kg
0.55 kWh
41 l
1:35 h
Automatic load sensing
Delicates/Silk – – (cold)
2 kg
0.04 kWh
35 l
0:41 h
Independently of the load display, the automatic load sensing function uses additional sensors to adapt the water and
power consumption ideally to each programme, depending on the type of fabric and the load.
Delicates/Silk 30 °C
2 kg
0.14 kWh
35 l
0:41 h
Outdoor Fabrics
Laundry must not be treated with fabric softener.
Wool – – (cold)
2 kg
0.06 kWh
40 l
0:40 h
Waterproofing
Clean the detergent drawer thoroughly to remove fabric softener residue.
2 kg
0.16 kWh
40 l
0:40 h
Wool 30 °C
Special detergent and waterproofing agent suitable for machine washing are available from sports shops.
Dosage according to the manufacturer's instructions:
* Programme setting for testing and energy labelling in accordance with EU Directive 92/75/EEC.
** Programme setting for testing in accordance with applicable standard EN60456.
1. Place the special detergent for outdoor clothing in compartment II and
Note on comparative tests: When testing the test programmes, wash the specified load using the maximum spin speed.
2. pour impregnating agent (max. 170 ml) into the
As a short programme for coloureds, select the programme Mixed Fabrics 40 °C and the maximum spin speed.
Set the programme selector to Outdoor Fabrics Waterproofing. Set the temperature.
Press Start/Reload. Final treatment of the laundry in accordance with the manufacturer's instructions.
*** The values may deviate from the indicated values depending on water pressure, water hardness, and water inlet tempera-
ture, ambient temperature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and
selected additional functions.
8
Insert for liquid detergent
depending on model
Position the insert for dispensing liquid detergent:
– Remove the detergent drawer completely
page 10.
– Slide the insert forwards.
Do not use the insert (slide upwards):
– for gel detergents and washing powder
– for programmes with
Pre-wash and the End time option.
Care
– Risk of electric shock. Disconnect the mains plug.
– Risk of explosion. No solvents.
Machine housing, control panel
– Remove detergent residue immediately.
– Wipe with a soft, damp cloth.
– Do not clean with a jet of water.
Cleaning the detergent drawer ...
... if it contains detergent or fabric softener residues.
1. Pull out, press the insert down, remove the drawer completely.
2. To remove the insert: press the insert upwards from below with your finger.
3. Clean the detergent dispenser tray and insert with water and a brush and dry it.
4. Fit the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Leave the detergent drawer open so that any residual water can evaporate.
fabric softener
Drum
Use chlorine-free cleaning agent, not steel wool.
Descaling
No laundry in the machine.
This should not be necessary if the detergent is measured out correctly. If it does become necessary, however, proceed
according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or
from our after-sales service (page 13).
Information on the display panel
depending on model
Door open?
Close the washing machine door properly; laundry may be caught.
Tap closed?
Open the tap completely, supply hose kinked or trapped; Clean the filter
water pressure too low.
Pump blocked!
Detergent solution pump blocked; Clean the detergent solution pump
page 11.
Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon
Pause no Top-up;
Not possible to add laundry.
Water level too high or
To continue, press the Start/Reload button.
Temperature too high
F: 23
Water in the base tub, appliance leaking. Call the after-sales service.
F: 34
Washing machine door cannot be locked. Open the washing machine door and close it so
that you hear it "click"; switch the appliance off and on again; set the programme and make
your settings; start the programme.
compartment.
Other displays
Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears
again, call the after-sales service
page 13.
9
– Risk of scalding.
Allow the detergent solution to cool down.
Information about blockages
What to do if...
– Turn off the tap.
Detergent solution pump
...Water is escaping:
Turn the programme selector to Off and disconnect the mains plug.
...No water is entering the drum: – Start/Reload not selected?
1. Open and remove the service flap.
2. Take the drainage hose out of the retainer.
...Washing machine door cannot
Remove the sealing cap, allow the detergent solution to flow out.
be opened:
Push the sealing cap back on.
...Programme does not start:
3. Unscrew the pump cover carefully (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
...Detergent solution
solution pump must be able to rotate).
does not empty.
...Water not visible in the drum: – Not a fault - water below the visible area.
5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the
Unsatisfactory spin result.
Laundry wet/too damp.
drainage hose in the holder.
6. Refit the service flap and close it.
...The progr. duration changes
To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into
during the washing cycle:
compartment II and start the Drain programme.
...Spinning is restarted several
times:
Drainage hose at the siphon
...Residual water in the
Turn the programme selector to Off and disconnect the mains plug.
partment for care products:
1. Loosen the hose clamp, remove the drainage hose carefully (residual water).
...Odours build up in the washing
2. Clean the drainage hose and siphon connecting piece.
machine:
3. Reattach the drainage hose and secure the connection with the hose clamp.
...The
status display
Filter in the water supply
lights up:
Foam may be escaping from the
Risk of electric shock
detergent drawer:
Do not immerse the HydroSafe safety device in water (it contains an electric valve).
page 11,
...Loud spinning, vibrations and
Reduce the water pressure in the supply hose:
"walking" during the spin cycle:
1. Turn off the tap.
page 11.
2. Select any programme (except Spin / Drain).
3. Select Start/Reload. Let the programme run for approximately
...Noises emitted during
40 seconds.
spinning and emptying:
4. Turn the programme selector to Off. Disconnect the mains plug.
...Display panel/indicator lamps
do not function during
operation:
5. Clean the filter:
Disconnect the hose from the tap.
Clean the filter with a small brush.
and/or for Standard and Aqua-Secure models:
...Programme sequence longer
Remove the hose from the rear of the appliance.
than usual:
Remove the filter with pliers and clean.
6. Connect the hose and check for leaks.
...There is detergent residue
on the laundry:
10
11
What to do if ...
– Attach/replace the drainage hose correctly.
in Reload mode, Start/Reload
– Water level too high. Close the washing machine door immediately.
– Tighten the screw connection of the supply hose.
flashes very quickly and an
– To continue, press the Start/Reload button.
audible signal sounds:
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Tap not turned on?
– Filter blocked? Clean the filter
page 11.
– Turn the programme selector to Off and remove the mains plug from the socket.
– Supply hose kinked or trapped?
– Turn off the water supply and call the after-sales service
page 13.
– Safety function active. Programme stopped?
page 4.
–
Rinse Hold (no final spin) selected?
page 3,4.
Emergency release
e.g. in the event of a power cut
– Can be opened by emergency release only?
page 13.
– Start/Reload or End time selected?
The programme continues when the power supply is restored. However, if the laundry has to be removed, the washing
– Washing machine door closed?
machine door can be opened as follows:
– Childproof lock active? Deactivate
page 5.
–
Rinse Hold (no final spin) selected?
page 3,4.
Risk of scalding
– Clean the detergent solution pump
page 11.
The detergent solution and laundry may be hot. If possible, leave to cool down.
– Clean the waste pipe and/or drainage hose.
Do not reach into the drum if it is still rotating.
Do not open the washing machine door if water can be seen through the glass.
1. Turn the programme selector to Off and disconnect the mains plug.
– Not a fault - the unbalanced-load detection system interrupted spinning, uneven
2. Drain the detergent solution
page 11.
laundry distribution.
3. Pull the emergency release downwards with a tool and release.
Distribute large and small items of laundry evenly in the drum.
The washing machine door can then be opened.
–
Less Ironing selected?
page 5.
– Speed selected too low?
page 5.
After-sales service
– Not a fault - the programme sequence is optimised for the relevant washing pro-
cess. This can cause changes in the programme duration in the display panel.
If you cannot remedy the fault yourself (What to do if ...,
page 12, 13), contact our after-sales service. We will always
– Not a fault - unbalanced-load detection system is adjusting the imbalance.
find a suitable solution to avoid unnecessary visits by repair personnel.
com-
– Not a fault - the action of the care product is not affected.
The contact details of your nearest after-sales service can be found here or in the after-sales service directory
(model-dependent).
– Clean the insert if necessary
page 10.
– Run the Cottons/Coloureds 90 °C programme without laundry. Use standard
Please give the after-sales service the product number (E-Nr.) and the production (FD) number of the appliance.
detergent.
This information can be found:
– Too much detergent used?
on the inside of the washing machine door*/opened service
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into
flap* and rear of the appliance.
compartment II (not for outdoor or down fabrics).
*model-dependent
Product number
Production number
– Reduce the detergent dosage for the next wash cycle.
Trust the manufacturer's competence. Turn to us.
– Are the appliance feet fixed?
You will thereby ensure that the repairs are performed by trained service personnel equipped with original repair parts.
Secure appliance feet
Installation instructions.
– Transportation safety devices removed?
Remove transportation safety devices
Installation instructions.
– Clean the detergent solution pump
page 11.
– Power cut?
– Circuit breakers tripped or fuses blown? Reset the circuit breakers or change the
fuses.
– Energy saving mode active?
page 1.
– If the fault occurs repeatedly, call the after-sales service.
– Not a fault - unbalanced-load detection system is adjusting the imbalance by
repeatedly redistributing the laundry.
– Not a fault - foam detection system active - several rinse cycles are added.
– Occasionally, detergent powder contains water-insoluble residues.
– Select the Rinse programme or brush out laundry.
– Use liquid detergent
12
Observe the
safety instructions
on page 8.
Washing
machine
Instruction manual
en
Read these instructions and the
separate Installation instructions before
operating the washing machine.
13