Epson dreamio EMP-TW500 Setup-Handbuch

Blättern Sie online oder laden Sie pdf Setup-Handbuch für Projektor Epson dreamio EMP-TW500 herunter. Epson dreamio EMP-TW500 2 Seiten. Dreamio home projector
Auch für Epson dreamio EMP-TW500: Betriebshandbuch (36 seiten), Spezifikationen (2 seiten), Benutzerhandbuch (9 seiten)

Seite drucken

Setup Guide

Setting up

Adjust the projection size.

The size of the projected image is basically determined by

the distance from the projector's lens to the screen.

Projection distance

The height from the centre of the lens to the bottom of

the screen will vary depending on the lens shift setting.

Refer to the table below to the projector so that the images are

projected onto the screen at the optimum size.

Units: cm (in.)

Shortest

16:9 screen size

(Zoom adjustment:

Wide)

30"

66 × 37 (26 × 14)

40"

89 × 50 (34 × 19)

60"

130 × 75 (52 × 29)

70"

154 × 87 (61 × 34)

80"

180 × 100 (69 × 39)

100"

220 × 120 (87 × 49)

200"

440 × 250 (174 × 98)

300"

660 × 370 (261 × 147)

Units: cm (in.)

Shortest

4:3 screen size

(Zoom adjustment:

Wide)

30"

61 × 46 (24.0 × 18.1)

40"

81 × 61 (31.9 × 24.0)

60"

120 × 90 (47.2 × 35.4)

70"

142 × 106 (55.9 × 42.0)

80"

160 × 120 (63.0 × 47.2)

100"

200 × 150 (78.7 × 59.1)

200"

410 × 300 (161.4 × 118.1)

300"

610 × 460 (240.2 × 181.1)

1119–1672 (36.7–54.9)

Lens shift adjustment

The lens shift adjustment can be used to position the image without distorting it

and is especially useful when using the projector in the following locations.

Hanging from a ceiling

A screen in a high location

Projector situated to the side so that the screen can be viewed sitting right in front of it

Projector situated on a shelf, etc.

Adjusting the projection screen" - Projection image position adjustment (Lens shift)

* The dotted lines indicate the projection range from the lens centre position.

Connecting image sources

Turn the power off for both the projector and the signal source before connecting them. If the power for

either device is on at the time of connection, damage may result.

Check the shapes of the cable connectors and the device ports before making the connections. If you try to

force a connector to fit a device port with a different shape or number of terminals, a malfunction or damage

to the connector or port may result.

Video equipment (VHS VCR, DVD player, game console, etc.)

*Port names may vary depending on the equipment being connected.

SCART

Component

SCART cable

(commercially-

available)

Component video cable

RGB SCART

(commercially-available)

adapter*

(accessory)

G B R Y

*Push the

connectors

in as far as

they will go.

*1 If a DVD has been connected using an RGB SCART adapter, change the "InputA" or "InputB" setting to "RGB-Video".

*2 Some regions may not have the RGB SCART adapter included as an accessory.

Projection methods

When projecting from directly in front

90°

Centre of lens

Screen

Avoid setting the projector up in places which are very dusty such as

bedrooms.

Units: cm (ft.)

Clean the air filter at least once every 3 months.

Projection distance

Clean the air filter more frequently if using the projector in a dusty

Longest

environment.

(Zoom adjustment:

–

Tele)

87–133 (2.9–4.4)

Installing the cable cover

118–179 (3.9–5.9)

179–270 (5.9–8.9)

Once the video equipment or computer has been connected, you can

then install the cable cover that is included with the projector to cover

209–316 (6.9–10.4)

the connectors for a neat appearance.

240–361 (7.9–11.9)

301–452(9.9–14.8)

Installation

606–909 (19.9–29.8)

Insert the two tabs inside the cable cover into the

911–1365 (29.9–44.8)

notches in the projector.

Units: cm (ft.)

Secure the cable cover by tightening the two fixing

screws.

Projection distance

Longest

(Zoom adjustment:

–

Tele)

108–164 (3.6–5.4)

146–220 (4.8–7.2)

221–332 (7.2–10.9)

258–388 (8.5–12.7)

295–443 (9.7–14.6)

370–555 (12.2–18.2)

745–1114 (24.4–36.5)

Video

S-Video

S-Video cable

RCA video cable

(commercially-

available)

When projecting from the side of the screen

When installing against a wall, leave a space of 20 cm (7.9 in.) or more between the

projector and the wall.

A special method of installation is required in order to suspend the projector from a ceiling.

Please contact your dealer if you would like to use this installation method.

If installing on a ceiling, you can change

the orientation of the EPSON logo plate

that would otherwise be upside-down.

Press your finger against the air exhaust

end of the plate. The opposite end of the

plate will lift up, so that you can pull it out

slightly and turn it around.

Removal

Loosen the fixing screws until

they come away from the

projector, and then lift up the

cable cover to remove it.

Securely tighten.

You can use a Phillips

screwdriver or a coin to tighten

the fixing screws.

Centre of lens

Lens at maximum left

Lens at maximum right

Some signal sources may have specially-

shaped ports. In such cases, use the

accessory or optional cables that are

supplied with the signal source to make the

connections.

Computer

HDMI

Computer

cable

(commercially-

available)

HDMI cable

BNC

RCA

(commercially-

adapter

available)

connector

(

commercially-

available

)

*Attach the adapter connector to

the computer cable and then

connect it to the projector.

Selecting the image source in

When suspending the

When projecting from a ceiling

projector from a ceiling,

change the configuration

menu settings.

Configuration menu

Setting

Screen

Projection

Lens at maximum up

Lens at maximum down

Remote control preparation

Inserting batteries into the remote control

The remote control is not supplied with batteries already inserted.

Insert the accessory batteries before using the remote control.

Remove the battery cover.

Insert the batteries.

Check the (+) and (-) indications inside

the battery compartment and insert the

batteries so that they face correctly.

While pressing

the knob, lift up.

Install the battery cover.

Insert the tab.

Press down until the battery

cover clicks into place.

Operating range (horizontal)

Remote control light-receiving area

Operating

distance

Approx. 10 m

(30 ft.)

Approx. 30°

Remote control

light-emitting

area

Operating range (vertical)

Operating distance

Approx. 10 m (30 ft.)

Approx. 30°

Battery replacement period

If delays in the responsiveness of the remote control occur or if it does

not operate after it has been used for some time, it probably means that

the batteries are becoming flat. If this happens, replace the batteries

with two new batteries. Use two new AA alkaline batteries as

replacement batteries.

Continued

Front

Front/Ceiling

Approx. 30°