ActronAir CP05 Installationshandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Installationshandbuch für Zubehör für Klimageräte ActronAir CP05 herunter. ActronAir CP05 16 Seiten. Control interface

Seite drucken

CP05 & CP10 CONTROL INTERFACE INSTALLATION GUIDE

SAFETY PRECAUTIONS

1. 1. Read all instructions in this manual before operating the air conditioning unit. Failure to do so may result in

Read all instructions in this manual before operating the air conditioning unit. Failure to do so may result in

damage to the unit and void your warranty.

2. 2. Turn-Off power from mains supply by removing fuse or switching the circuit breaker to the "Off" position

Turn-Off power from mains supply by removing fuse or switching the circuit breaker to the "Off" position

before installation or servicing this control interface.

3. 3. Follow sound Lock Out & Tag Out procedures to ensure that power supply is not re-energised accidentally.

Follow sound Lock Out & Tag Out procedures to ensure that power supply is not re-energised accidentally.

4. 4. This control interface has power supply from the control board via telephone connector, with voltage of

This control interface has power supply from the control board via telephone connector, with voltage of

18-30VDC Class II & maximum power input of 0.5W. Ensure that this unit is not installed on voltages higher

than 30V DC supply.

5. 5. Ensure that the unit installation complies with relevant council regulations and building code standards.

Ensure that the unit installation complies with relevant council regulations and building code standards.

All electrical wiring must be in accordance with current electrical authority regulations and all wiring

connections to be as per electrical diagram provided.

6. WH&S rules and regulations must be observed and will take precedence during installation process.

7. Only use this Control Interface with an ActronAir air conditioner as described in this installation guide.

INTRODUCTION

This guide covers the installation and application of ActronAir CP05 and CP10 control interfaces. Functions,

graphic displays and operations of both control interfaces are identical, therefore the two interfaces can be

interchangeable parts and can also be combined as a dual control with mimic logic. Except for the character

height, some difference in button symbols, and the physical size, shape and colour of the casings, both control

interfaces provide the control flexibilty required for your air conditioning system's optimum operation. Note that

there is also a minor difference in addressing the Mimic display procedures, which is explained in the affected

steps below.

The CP05 and CP10 graphic display are electronic devices which are compatible with ActronAir commercial

control systems. The control interfaces allow complete management of graphics by the display of icons,

management of international fonts and acoustic signal through piezoelectric buzzer. The display icons are

defined at the application software development level while the fonts are in two sizes of 6x8 and 12x16 pixels.

The application software resides on the outdoor controller, therefore the control interfaces does not require any

additional software for operation.

The standard control set up for the Hercules and Large Commercial units provides a single display monitor. This

is either a CP05 or CP10 Control Interface which is mounted on the unit's electrical panel. There are situations

where monitoring is required away from the unit, such as in a control room or in bulding management office.

The ideal solution to such requirement is to provide a secondary control interface, which acts as a dual control

interface. The secondary control interface will be wired to the system and can be mounted away from the unit.

The dual control interfaces mimic each other, however the control interface most recently accessed has the

priority over the other. For your dual control interface, you may have an option to use two CP05, two CP10 or one

CP05 and one CP10, depending on your situation and requirement.

The following procedures will dicuss the installation, configuration, specifications, components required and

addressing the Mimic display of your dual control interface.

IMPORTANT NOTES

1. 1. Please read this guide thoroughly and understand the procedure before performing the installation and

Please read this guide thoroughly and understand the procedure before performing the installation and

configuration of your Control Interface.

2. 2. Only

Only qualified technicians

qualified technicians* * are allowed to perform these procedures.

and installer, assume all liability and risks relating to the configuration of the product in order to reach the

expected results in relation to the specific design and system installation. Actron Air, based on specific

agreements, may be consulted for the positive commissioning, installation and application of the unit, however

in no case does it accept liability for the correct operation of the final equipment / system.

* *

Qualifications required will be appropriate Electrical, Refrigeration and Refrigerant Handling License & Training, dependent on local State/Territory regulations.

are allowed to perform these procedures. The customer, both end user, specifier

CP05 - CP10 Control Interface Insert

Doc. No.0525-035 Ver. 6 220307