ACU-RITE 02033 Gebrauchsanweisung - Seite 11

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Wetterstation ACU-RITE 02033 herunter. ACU-RITE 02033 13 Seiten. Professional weather center

Seite drucken

The preference set order is as follows:

OUTDOOR TEMPERATURE

OUTDOOR HUMIDITY

INDOOR TEMPERATURE

INDOOR HUMIDITY

BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*

*To change from AUTO to MANUAL pressure mode and vice versa, press AND

HOLD the "SET" button for at least 10 seconds. The display indicates the current

pressure mode selected,"AUTO" or "MANUAL".

After 20 seconds of inactivity, the display will save the adjustments and exit calibration

mode. Note: Calibrations will be erased if the display is reset or if batteries are

removed and the power adapter is unplugged.

Calibrate the Rain Gauge

The rain gauge on the 5-in-1 sensor can be calibrated to improve accuracy.

Items Needed: 5-in-1 sensor, display, plastic cup, pin, screw driver

1. First, ensure 5-in-1 sensor is perfectly level using built-in bubble level.

2. Place display close so you can monitor it during calibration.

3. Make a pin hole in the bottom of a plastic cup. Hold the cup over the rain gauge and fill

it with exactly 8oz (236 ml) of water, allowing the water to drip into the rain gauge. You

should hear the internal buckets tip and see water drain through the rain gauge.

4. A few seconds after each bucket tip, the display displays rainfall in approximately

0.01" (.254 mm) or more increments.

5. The cup of water should take more than 20 minutes to empty; a quicker period will

result in inaccurate calibration. Try to simulate a normal steady rainfall. When cup is

empty of water, display should register 1.06" (26.92 mm).

Tips

• There should be nearly an equal number of water drops (about 25 water drops)

between bucket tips. If not, adjust the calibration screws on the bottom of the 5-in-1

sensor until an equal number of water drops are tipping the buckets. Then, restart the

calibration procedure.

• If you don't hear the buckets tipping and see water dripping alternately out of

each drain, there may be an issue with the rain gauge or it's adjustment. See

Troubleshooting on page 18.

Adjustment

If the rain gauge doesn't register close to 1.06" (26.92 mm), make an EQUAL

adjustment to the two calibration screws on the bottom of the 5-in-1 sensor. Turning

screws clockwise increases rainfall; counter clockwise decreases rainfall.

• To adjust the rainfall reading by 2% turn both screws 1/8 of a turn.

• To adjust the rainfall reading by 4% turn both screws 1/4 of a turn.

• To adjust the rainfall reading by 8% turn both screws 1/2 of a turn.

Watch the video at www.acurite.com/5n1

Specifications

TEMPERATURE RANGE

Outdoor: -40ºF to 158ºF; -40ºC to 70ºC

Indoor: 32ºF to 122ºF; 0ºC to 50ºC

HUMIDITY RANGE

Outdoor: 1% to 99%

Indoor: 1% to 99%

WIND SPEED

0 to 99 mph; 0 to 159 kph

WIND DIRECTION

16 points

INDICATORS

RAINFALL

0.01 inches (0.25 mm) and up

WIRELESS RANGE

330ft / 100m

OPERATING FREQUENCY

433 MHz

POWER

Display: 5V 250mA AC Adapter

3 x AA alkaline batteries (optional)

Sensor: 4 x AA alkaline or lithium batteries

DATA REPORTING

Wind Speed: 18 second updates; Direction: 36 seconds

Outdoor temperature & humidity: 36 second updates

Indoor temperature & humidity: 60 second updates

PC Connect CSV Data Logging: 12 minute intervals

PC Connect to AcuRite Software/App: 18 seconds

DISPLAY MEMORY

512 kilobytes (not expandable)

PC CONNECT SYSTEM

Mac OSX 10.9 (Mavericks) or higher

REQUIREMENTS

Windows 10 / 8.1 / 8 / 7; 1 GHz or faster processor;

1 GB (32-bit) or 2 GB (64-bit) of RAM; available USB 2.0 port

High speed internet is required for some advanced features of

PC Connect, such as Weather Underground Rapid Fire Updates.

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:

1- This device may NOT cause harmful interference, and

2- This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could

void the user authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

depending on home construction materials