Cisco WAP2000 Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Drahtloser Zugangspunkt Cisco WAP2000 herunter. Cisco WAP2000 2 Seiten. Wireless-g access point with power over ethernet

Seite drucken

Line up the WAP2000 so that the wall-mount slots on the bottom of the

TEP

access point line up with the two screws.

Place the wall-mount slots over the screws and slide the access point

TEP

down until the screws fit snugly into the wall-mount slots.

Americas Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

http://www.cisco.com

Tel: 408 526-4000

800 553-NETS (6387)

Fax: 408 527-0883

Cisco, Cisco Systems, the Cisco logo, and the Cisco Systems logo are registered trademarks or trademarks of Cisco Systems,

Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or

Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0705R)

Printed in the USA on recycled paper containing 10% postconsumer waste.

78-19136-01

Connecting the Equipment

You can connect the WAP2000 to your network in one of the following ways:

• Using a PoE router or switch

• Using a standard router or switch

Using a PoE Router or Switch to Connect the WAP2000

To connect the WAP2000 to your network using a PoE router or switch, use the

supplied Ethernet cable to connect the Ethernet port of the access point to a

PoE port on the PoE router or switch.

The LEDs on the front panel light up as soon as the WAP2000 powers on.

Using a Standard Router or Switch to Connect the WAP2000

To connect the WAP2000 to your network using a standard switch, follow these

steps.

Use the supplied Ethernet cable to connect the Ethernet port of the

TEP

access point to an Ethernet port on the router or switch.

Connect the included power adapter to the Power port of the

TEP

WAP2000.

Plug the power adapter into an electrical outlet.

TEP

The LEDs on the front panel light up as soon as the WAP2000 powers on.

Verifying the Hardware

Installation

To verify the hardware installation, complete the following tasks:

• Check the cable connections.

• Check the LED states, as described in

Getting to Know the WAP2000,

page

If you need help resolving a problem, visit the Cisco Small Business

OTE

Support Community at www.cisco.com/go/smallbizsupport. For

technical documentation and other links, see

Where to Go From

Here, page

Configuring the Device

The firmware v2.0.3.4 or later releases changed the factory default IP address

configuration to DHCP. Before installation, make sure your DHCP server is

running and can be reached. You may need to disconnect and reconnect the

devices for them to discover their new IP addresses from the DHCP server.

If the WAP2000 access point does not receive a DHCP response after 60

seconds, it falls back to the following default static IP address: 192. 1 68. 1 .245

and a default mask of 255.255.255.0.

To configure the access point, follow these steps to access the device's web-

based configuration utility from your computer.

Connect the WAP2000 Access Point to the same network as your

TEP

computer.

Locate the IP address of the WAP2000 Access Point by accessing

TEP

your DHCP server. Specific instructions on locating the DHCP address

given to the WAP2000 Access Point depends upon the type of

architecture and operating system you are using. Use your computer's

local Help and Support functionality and search for "IP Addressing".

Launch a web browser, such as Internet Explorer or Mozilla Firefox.

TEP

In the Address field enter the default DHCP address and press the

TEP

Enter key.

In the User Name and Password fields enter the default of admin.

TEP

Click OK.

TEP

Suggested Next Steps

Congratulations, you are now ready to begin using your WAP2000. You may

wish to consider taking some of the following steps:

• Change the default password of the access point to protect it from

unauthorized use.

• Depending on your deployment requirements, you might need to change

some of the configuration parameters of the access point.

• Update the firmware version.

• For more information on how to change the password and configure the

access point, refer to the

Cisco WAP2000 Wireless-G Access Point with

Power Over Ethernet Administration Guide

. This guide is on the CD-ROM

that comes with the product. You can also access this guide and other

related documentation on Cisco.com, as indicated in the next section.

Where to Go From Here

Support

Cisco Small Business Support

www.cisco.com/go/smallbizsupport

Community

Online Technical Support and

www.cisco.com/support

Documentation (Login Required)

Phone Support Contacts

www.cisco.com/en/US/support/

tsd_cisco_small_

business_support_center_contacts.html

Software Downloads

Go to tools.cisco.com/support/downloads,

(Login Required)

and enter the model number in the Software

Search box.

Product Documentation

Cisco WAP2000 Wireless-G

http://www.cisco.com/en/US/products/

Access Point with Power Over

ps10049/index.html

Ethernet

Cisco Small Business

Cisco Partner Central for Small

www.cisco.com/web/partners/sell/smb

Business (Partner Login

Required)

Cisco Small Business Home

www.cisco.com/smb

Marketplace