Argo AW726CL Betriebsanleitung - Seite 7

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Klimagerät Argo AW726CL herunter. Argo AW726CL 16 Seiten.

Seite drucken

NOTE

Use DRY operation when you want to reduce the humidity

in the room.

Once the room temperature reaches the set level, the unit

repeats the cycle of turning on and off automatically.

During DRY operation, the fan speed is automatically set

or stops to prevent overcooling.

Dry operation is not possible if the indoor temperature is

15 °C or less.

FAN ONLY

If you want to make air circulate without any temperature control,

follow these steps:

1. Press the ON/OFF operation button and switch the air

conditioner ON.

2. Press MODE button until only the

the display.

ADJUSTING THE FAN SPEED

AUTOMATIC

Simply set the FAN selector to the

microcomputer automatically controls the fan speed when

the AUTO mode is selected. When the air conditioner starts

operating, the difference between the room temperature

and the set temperature is detected by the microcomputer

which then automatically switches the fan speed to the

most suitable level.

WHEN DIFFERENCE BETWEEN

ROOM TEMPERATURE AND SET

TEMPERATURE IS

Cooling and

2 °C and over

dehumidifying

Between 2 and 1 °C

modes:

Below 1 °C

2 °C and over

Heating mode:

Below 2 °C

NOTE

The above mentioned data make reference to the air

conditioner operating when the sensor on the remote control

unit is ON. (Refer to temperature sensor selector). If the

sensor on the indoor unit is being used then actual operation

will slightly differ from that described in the above tables.

The automatic speed is not available in FAN ONLY mode.

MANUAL

If you want to manually adjust speed just set the FAN selector

as desired.

High speed

Med. speed

NIGHT MODE

The NIGHT mode enables you to save energy.

1. Set the MODE selector to cool, dry or heat.

2. Press the NIGHT button.

3. The

mark appears on the display. Press the NIGHT

button again to release the NIGHT function.

What does the NIGHT mode mean?

In this mode, the air conditioner will cool or heat the room to the

set temperature, and then the thermostat will make the unit pause.

After about 1 hour, the air conditioner will automatically reset the

set temperature as follows (also refer to graphs).

Cooling and Dehumidifying

When the room temperature reaches the new set value,

the thermostat will cause the unit to pause. After about 1

hour the temperature will be raised by 1 °C in cooling, or

lowered by 1 °C in heating. This enables you to save energy

without sacrificing your comfort.

COOLING AND DEHUMIDIFYING

Setting temperature Room temperature

fan sign appears on

position.A

SETTING THE TIMER

A) HOW TO SET THE ON TIME

1. Press the SEL TYPE button once.

The ON and time indications flash.

2. Press the SET H button until the

designed hour is displayed.

Press the SET M button until the

designed minutes are displayed. The

FAN SPEED

display will change automatically back

to show the present time after 10 sec.

3. Press the ON/OFF button to start the air

High

conditioner.

Medium

4. Press the TIMER SEL button to activate

Low

the ON timer.

High

B) HOW TO SET THE OFF TIME

Medium

1. Press the SEL TYPE button twice.

The OFF and time indications flash.

2. Press the SET H button until the

designed hour is displayed.

Press the SET M button until the

designed minutes are displayed. The

display will change automatically back

to show the present time after 10 sec.

3. Press the ON/OFF button to start the air

conditioner.

4. Press the TIMER SEL button two times

to activate the OFF timer.

Low speed

C) HOW TO SET A PROGRAM FOR

DAILY ON/OFF OPERATION (OR

VICEVERSA)

1. Set the timer ON/OFF as shown in A)

and B).

2. Press the ON/OFF button to start the air

conditioner.

3. Press three times the TIMER SELECT

button to activate the DAILY timer.

NOTE

After timer setting, press PROGRAM button in order to

check the ON/OFF setting time.

OPERATING MODE

SET TEMPERATURE CHANGE

Heating

Setting temperature Room temperature

1°C

1 hour 1 hour TIME

Lowered by 1 °C

Raised by 1 °C

HEATING

1°C

1 hour

1 hour TIME