Cisco TelePresence MX300 Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Handbuch für Konferenz-System Cisco TelePresence MX300 herunter. Cisco TelePresence MX300 2 Seiten. Telepresence c series telepresence mx series telepresence sx series telepresence ex series
Auch für Cisco TelePresence MX300: Handbuch "Erste Schritte (42 seiten), Kurzreferenz-Handbuch (2 seiten), Schnellstart-Handbuch (12 seiten), Kurzreferenz-Handbuch (2 seiten), Handbuch zur Fehlersuche (37 seiten), Handbuch "Erste Schritte (46 seiten)

Seite drucken

Installing Cisco TelePresence MX300 - Floor Stand

Connecting the cables

Connect the cables. The connectors are placed at the rear

side of the LCD video unit. See illustration for details.

Lead the cables down the cable channel.

Power

switch

iii

Snap on the cable channel

lid for strain relief.

Power

Note:

When you position

supply

the cables side by side it

is easier to snap on the lid.

Lead the cables in the cable slots in the floor stand. Be

careful to put the cables below the hooks.

You can lead the cables out at the front or back of the system

as appropriate.

Note:

If cables are longer than you need, you can lead them

around the cable slot several times. If more convenient, do

this before connecting the cables to the unit.

Switching on the system

Local area

Plug in the cables from the LCD video unit as appropriate, and

network (LAN)

make sure the Touch controller is connected.

SAFETY REQUIREMENT:

The equipment shall be installed close to

Touch controller

the socket outlet. The socket outlet shall be easily accessible after

installation.

Switch on the system.

PC video input

The power switch is located above the power connector on the

rear side of the LCD video unit.

PC audio input

Snapping on the floor stand covers and back cover

Audio line output

(cable not included)

Ensure that the cables are placed

Microphones

under the hooks in the cable slots.

AC Input

Then snap on the two floor stand

For maintenance only

covers, one at a time. The covers are

Reset factory settings

fastened with magnets when they are

lowered toward the base.

6 ,

45,7

LCD video unit connectors

Finishing up

iii

Wait while the MX300 starts up. Normally this takes just a few

Remove the protective foil from the LCD video unit.

minutes. If an automatic software upgrade occurs the start-up

If required, clean the Touch display (not the LCD video

process may take up to 15 minutes.

display) using the dry cleaning cloth provided.

When the home menu and contact list appear on the Touch

iii

Unfold the rear-mounted foot on the Touch controller to

controller the system is ready to use.

increase its tilt.

CAUTION:

To alter the camera position always use the Camera

Control panel on the Touch controller; never move the camera

manually when the power is switched on.

EMC A-Class declaration

Snap on the back cover to

此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种

hide the connectors and

情况下，可能需要用户对其干扰采取切实可行的措施。

cables.

The back cover is delivered

WARNING: This is a class A product. In a domestic environment

WARNING:

This is a class A product. In a domestic environment this

in a separate box.

this product may cause radio interference in which case the user

product may cause radio interference in which case the user may be

required to take adequate measures.

may be required to take adequate measures.

You can lock/unlock the back

cover by lifting this handle.

Use both hands if required.

On our web site you will find an overview of the

worldwide Cisco contacts.

Go to: http://www.cisco.com/web/siteassets/contacts.

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Dr.

San Jose, CA 95134 USA

LCD video unit placement

The placement of the video system in a room will influence the

overall conferencing experience both at the local and remote

sites.

You should aim for:

•

Good illumination of a person's face to avoid annoying

shadows.

•

No direct light on the LCD video display to avoid reflections.

The illustrations to the right show in general where to place your

MX300 system depending on the window positions in the room.

For each room layout the MX300 position(s) marked with A are

preferred, then B and finally C. You should avoid any position

not shown in the illustrations.

声明

Microphone placement

Correctly placed microphones are very important to obtain a

good conferencing experience.

We recommend that you place the microphone(s) as close to

all users as possible, and that you avoid putting equipment

with noisy fans, such as computers and projectors, close to a

microphone.

If you are using more than one microphone, place them far

apart to minimize the interference. The required distance

between the microphones depends on the acoustics of your

room; normally 2 m (6.5 ft) will suffice.

The MX300 internal microphone may suffice in a small office

or meeting room when all participants are closer to the display

than 2.5 m (8 ft). Still a correctly placed external microphone

often performs better. The internal microphone is automatically

disabled when connecting an external microphone.

If you want to learn more about optimizing your office

or meeting room for video conferencing, please read

the Video conferencing room primer and Guidelines

for video conferencing room acoustics documents

that are available on the Cisco web site,

http://www.cisco.com/go/telepresence/docs.