Cable-Tronix CT-HDVD-HDCX-IR Benutzerhandbuch

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Extender Cable-Tronix CT-HDVD-HDCX-IR herunter. Cable-Tronix CT-HDVD-HDCX-IR 2 Seiten. Hdmi rf extender over coaxial cable with ir

Seite drucken
Important safety notice
Please read below safety instructions carefully before installation and operation:
1. Please pay attention to all the warnings and hints on this device.
2. Do not expose this unit to rain, moisture or liquid.
3. Do not put anything on top of the device.
CT-HDVD-HDCX-IR
4. Do not repair or open this device without professional guidance.
5. Ensure good ventilation to avoid product overheating .
6. Shut off power and make sure the area is safe before installation.
HDMI RF Extender over Coaxial
7. Do not connect the network cables and IR cables when the device is on,
to avoid damage.
Cable with IR
8. Use DC5V only. Make sure the specification matches if using 3
DC adapters.
User Manual
1 Introduction
This HDMI over RF extender utilizes RF conversion technology to convert an
HDMI signal to an HD digital TV signal, and transmits it by coaxial cable up
to 700 meters. It provides a high quality image and anti-interference
capability and can be used with a CATV splitter to realize one to many, many
to many, and video matrix operations.
The HDMI extender can be applied to a wide variety of operations, such as
CCTV monitoring, large outdoor screens, shopping malls, education, digital
KVM fields, etc.
2
Features
1) Fully compatible with HDCP.
2) Transmit up to 700meters with RG6( 75 ) at 1080P@60Hz.
3) Support up to 100 channels.
4) Support CATV splitter and amplifier connection.
5) High quality image, long distance transmission and strong
anti-interference ability.
6) Supports IR remote switching at the receiver.
3
PACKAGE CONTENTS
HDMI to RF sender TX*1pcs
RF to HDMI receiver RX*1pcs
rd
party
Remote control
DC5V1A*2pcs
IR receiver extension
User's manual 1pcs
cable x1pcs
4
INSTALLATION REQUIREMENTS
1.HDMI source device(computer graphics card, DVD,PS3, HD monitor
equipment etc).
2.SDT V, HDT V or projector with HDMI por t.
3.RG6(
75
) or upper level coaxial cables.
5
Panel description
1. HDMI to RF sender TX
1
2
3
4
5
6
RF TX: RF signal send interface
IR IN: IR receiver extension
1
2
Connection
cable interface
RESET: Press to reset
3
DC5V: DC 5V power input
HDMI INPUT: HDMI signal input
5
4
6.1 One-to-one connection
2.RF to HDMI receiver RX
DVD
6.2 One-to-many conection：C o n n e c t one CATV splitter to utilize
1
2
3
4
5
splitter function.
RF RX: RF signal receive interface
LINK: signal connection led
1
2
IR IN: IR receiver extension cable interface
indicator
3
DC5V: DC 5V power input
HDMI OUTPUT: HDMI output
5
4
3. Channel parameters settings
2
DVD
Channel setting buttons
1
1
6.3 Many to many connection：Connect two CATV splitters to build
Channel display screen
2
video matrix.
There are 100 channels (0~99), selected with 2 buttons. The left
button changes the'singles'digit (on the right) and the right
button changes the "tens"digit (on the left). For eaxample, to set
channel "21", press the right button until the left digit is "2" and
DVD
press the left button until the right digit is "1". Connection
between a TX device and an RX device is only possible when both
DVD
devices are set to the same channel.
DVD
4. IR remote control
The IR remote is used solely to change the receive channel of the RX
Note: for above"CATV splitter 1", it needs to use"OUT"as the signal
device at the TV. For example, if there is a Playstation on channel 1, a
input and"IN"as signal output.
Blu-Ray player on ch 2 and a Satellite receiver on channel 3, use the
remote to choose ch1 to see the playstation, ch2 for the Blu-Ray etc.
For "CATV splitter 2", just follow the marks on the panel description.
*This channel selction is for the receivers only, and is not passed across the
coax to the transmitter(s).
6.4 Other notes
1. Cable length is suggested to be between 300 & 700 meters. If the cable
is shorter than 100 meters, a signal attenuator of at least 20db will be
needed. Choose an attenuator size which provides proper signal level at the
TV.
2. Refer to appendix 1 for channel-frequency mapping table; refer to
TX
RX
TV
appendix 2 for coaxial cable signal loss values for each channel frequency.
3. When using a CATV splitter for 1-to-many and many-to-many operation,
please use a bi-directional splitter with low insertion loss, high shielding and
a frequency range of at least 5 ~ 1000Mhz
RX
TV
OUT
OUT
OUT
4 WAY SPLITTER
SB-4 08E
4 WAY SPLIT TER
5-1000MHz
HIGH ISOLATION&SCREENING
HIGH ISOL ATION&SCREENING
OUT
IN
OUT
OUT
IN
RX
TV
TX
CATV splitter
RX
TV
7
F A Q
Q. It shows "NO SIGNAL" on screen.
A：1) Make sure to set TV source signal to the correct channel.
2) If link LED is not on, check if TX and RX channel settings are the same.
3) If coaxial cable is too long, please refer to Appendix 1 to adjust
TX
RX
TV
channel setting.
OUT
OUT
OUT
OUT
4 WAY SPLIT TER
5-1000MHz
SB-408E
4 WAY SPLIT TER
SB-408E
5-1000MHz
HIGH ISOL ATION&SCREENING
HIGH ISOL ATION&SCREENING
OUT
IN
OUT
OUT
IN
OUT
TX
RX
TV
CATV splitter 1
CATV splitter 2
Q. Image is not normal after setting channel (splash screen, disturbance,
TX
mosaic etc)?
RX
TV
A：Make sure coaxial cable connection is stable. Try a different channel or
power-cycle the TX unit.
Q：There is video image output but no sound?
A：Power-cycle the TX unit by disconnecting power for 20 seconds and
reconnect power.
OUT
SB-408E
5-1000MHz
OUT