DigiTech RPM1 Benutzerhandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Musikanlagen DigiTech RPM1 herunter. DigiTech RPM1 8 Seiten. Vacuum-tube rotary speaker emulator

Seite drucken

INPUT

LEFT (MONO)

RIGHT

Matching Bypass and

Effect levels

When setting up your

instrument volume and

RPM-1 Input levels, use

the Bypass button or the

Bypass footswitch to

alternate between the

Bypass and Effect sounds

while you are playing,

and adjust the Input con-

trol until the two levels

are equal.

If your instrument is out-

putting a very hot signal,

the 12AX7A tube will be

compressing and adding

warmth to the signal even

at minimum Drive set-

tings. This may be desir-

able, unless you need to

balance the Bypass level;

in that case, you should

turn the RPM-1 Input

control up to maximum

and then turn your instru-

ment volume down to

balance the levels.

Tri-Output mode

To use Tri-Output mode,

leave the Horn/Rotor

Balance control in the

center position, and

adjust the Spread control

to maximum Wide posi-

tion. Route the three out-

puts to three input chan-

nels on your mixer, pan

the LHorn and RHorn

outputs left and right and

pan Rotor center.

This gives you the most

flexibility by allowing you

to EQ and balance the

Left Horn, Right Horn

and Rotor sounds inde-

pendently. Try applying

reverb to both Horn out-

puts while leaving the

Rotor output dry.

OUTPUT

LEFT (MONO)

RIGHT

FOOTSWITCH

LHORN

RHORN

ROTOR

Stereo Inputs

Use Right and Left inputs for stereo, use

one plug only in the Left input for mono.

Outputs

Use the Left output for mono, Left and

Right for a stereo image of the rotating

effect, and LHorn, RHorn and Rotor to sim-

ulate two microphones on the horn (high

frequency) and one microphone on the

Rotor (low frequency).

Footswitch

Stereo 1/4" phone jack for the DigiTech

FS300 Footswitch (included)

Connection Diagrams

Mono

LEFT (MONO)

Mono output

of instrument

or mixer FX send

Turn Spread to Wide

Stereo

LEFT (MONO)

Mono or stereo

output of

instrument, or FX send

Mono

Left

Stereo Right

Tri-Output

LEFT (MONO)

Mono or stereo

output of

instrument, or FX send

Mono

Left

Stereo Right

CONTINUOUS

CONTROLLER

Rear Panel

Continuous Controller

For an optional volume pedal - controls the

rotor speed, overriding the Speed and Brake

buttons when a pedal is plugged in.

This input will use most passive volume pedals

or a 0–5 V control voltage pedal - plug a stan-

dard guitar cord between the pedal's output and

the Continuous Controller jack.

Plug the pedal in before you turn on the RPM-

1, then immediately after turning on the RPM-1,

sweep the pedal from its minimum to maximum

position to calibrate the response.

INPUT

OUTPUT

LEFT (MONO)

RIGHT

LHORN

RHORN

ROTOR

INPUT

OUTPUT

LEFT (MONO)

RIGHT

LHORN

RHORN

ROTOR

INPUT

OUTPUT

LEFT (MONO)

RIGHT

LHORN

RHORN

ROTOR

Turn Spread to Wide

CONTINUOUS

FOOTSWITCH

CONTROLLER

To Mixer or amplifier

FX Return or Channel

CONTINUOUS

FOOTSWITCH

CONTROLLER

To Mixer:

Right FX Return or Chan 1, pan Right

Left FX Return or Chan 2, pan Left

CONTINUOUS

FOOTSWITCH

CONTROLLER

To Mixer:

Chan 1, pan Center

Chan 2, pan Right

Chan 3, pan Left