DIGITECH Audio CS-2484 Benutzerhandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Redner DIGITECH Audio CS-2484 herunter. DIGITECH Audio CS-2484 4 Seiten. 12"/15" powered loudspeaker

Seite drucken
DIGITECH Audio CS-2484 Benutzerhandbuch
CS-2484 /CS-2486 REAR PANEL DESCRIPTION
LEVEL
1
MIN
MAX
2
LEVEL
MIC
INPUT
LINE
INPUT
3
MIN
MAX
VOLUME
R
L
4
MIN
MAX
TREBLE
5
LINE
-12
+12
BASS
6
-12
+12
CLIP
POWER
AC 240V 50Hz
6. XLR LINE Output – Using a XLR cable, use this port to daisy chain from your this speaker to other powered
speaker.
7.Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power
cord.
8.Fuse Holder – This housing stores the 3.15 amp GMA protective fuse. Always replace with the exact same type
fuse, unless otherwise instructed,
9. Microphone input Volume – This knob is used to increase or decrease the volume output on your speaker.
10. Line level input volume – This knob is used to regulate the output signal of theline level source connected to
the Line Level Inputs.
11. output volume – This knob is used to regulate the output signal being sent to other powered speaker.
12. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum
amount of treble gain is +12dB and the maximum amount of treble decrease is -12dB. Turning the knob in a
counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a
clockwise direction will increase the amount of treble applied to a channel signal.
13. Bass Control – This knob is used to regulate the amount bass applied to the
output signal. The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB.
Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal,
turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal.
14. Power indica tor led - LED lights up to indicate the speaker is on.
15. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume
to the point where the LED is blinking along with the bass beat.
16. MAIN POWER SWITCH - This is the main power ON/OFF button, Before main power is applied, be sure
you have made all connections to the speaker , Remember to avoid damaging pops to the speakers , the
mixer is turned on first and turned off last.
17. Mp3 player
5
1. Mic XLR Input - Plug a mic directly into this port for public address
usage and let your voice be heard.
2. 1/4" MIC Input – Plug a mic directly into this port.
17
3. Balanced RCA Li ne Input – This connection is designed to accept
a balanced line input signal from a mixeror other line level device
with a balanced output jack. Use a balanced cable when the signal
9
cable length exceeds 15 feet, this will reduce excessive signal loss.
Be sure to connect only line level input devices such as mixers
10
and tape machines to this jack.
11
4. Balanced XLR Li ne Input – This connection is designed to
accept a balanced line input signal from a mixer or other line level
12
device with a balanced output jack. Use a balanced cable when
13
the signal cable length exceeds 15 feet, this will reduce excessive
14
signal loss.5.1/4" Line Output Jack – This jack is used to send
15
the incoming line level signal from either of the Line Level Inputs
Jacks to other powered speaker.
5.1/4" Line Output Jack – This jack is used to send the
16
incoming line level signal from either of the Line Level
7
Inputs Jacks to other powered speaker.
8

Controls and Features

1
2
3
5
4
1.POLE MOUNT SOCKET-This socket is designed to fit a standard speaker
pole mount or tripod speaker stand.
2.RIGGING POINTS-This series speaker has rigging points . These points are
to be used to fly or suspend the speaker in the air by some means . Be sure
to follow the flying outlines.
3.HIGH FREQUENCY TRANSDUCER - This unit is used to reproduce the high
frequency response..
4.WOOFER-The high-powered woofer is used to reproduce the
midrange and low frequencies.
5.TRANSPORT HANDLE-This series speakers come with built-in
heavy-duty transportation handle . Use this handle for secure
and easy transportation.
6.POLE MOUNT LOCKING BOLT- This pin is used to secure the
speaker in place when mounting the speaker in a pole mount
configuration . Always be sure to tighten down on the locking
bolt to prevent the speaker from shifting during use.
5
2
CS-2486
5
LEVEL
MIN
MAX
LEVEL
MIC
INPUT
LINE
INPUT
MIN
MAX
VOLUME
R
L
MIN
MAX
TREBLE
LINE
-12
+12
BASS
-12
+12
CLIP
POWER
AC 240V 50Hz
6
3