Cisco 3600 Series Anhang - Seite 6

Blättern Sie online oder laden Sie pdf Anhang für Netzwerk-Hardware Cisco 3600 Series herunter. Cisco 3600 Series 15 Seiten. Memory upgrade
Auch für Cisco 3600 Series: Produktübersicht (10 seiten), Upgrade-Anweisungen (30 seiten), Benutzerhandbuch (17 seiten), Anwendungshinweis (41 seiten), Konfigurationshandbuch (36 seiten), Benutzerhandbuch (25 seiten), Benutzerhandbuch (7 seiten), Handbuch (5 seiten), Hinweis zur Konfiguration (23 seiten), Hinweis zur Konfiguration (18 seiten), Hinweis zur Konfiguration (25 seiten)

Cisco 3600 Series Anhang
Caller ID Configuration Task List
Command
Step 3
Router(config-voiceport)# voice confirmation-tone
Step 4
Router(config-voiceport)# dial-type {dtmf | pulse}
Step 5
Router(config-voiceport)# signal {loop-start |
ground-start}
Step 6
Router(config-voiceport)# codec {g729r8 | g729ar8 |
g726r32 | g711alaw | g711ulaw}
Step 7
Router(config-voiceport)# cptone locale
Step 8
Router(config-voiceport)# ring frequency {25 | 50}
Step 9
Router(config-voiceport)# caller-id attenuation
attenuation
Step 10
Router(config-voiceport)# ring number number
The following table lists the options that may be used for the locale variable with the cptone command.
Table 57
Command Option
ar
au
at
be
Cisco IOS Voice, Video, and Fax Configuration Guide
VC-816
Caller ID on Cisco 2600 and 3600 Series Routers and Cisco MC3810 Multiservice Concentrators
cptone Command Entries for the Cisco 2600 and 3600 Series
Country
Argentina
Australia
Austria
Belgium
Purpose
Enables the two-beep confirmation tone that a
caller hears when picking up the handset, if
connection plar or connection plar-opx is
configured.
(For FXO ports only) Selects the appropriate dial
type for out-dialing.
Selects the appropriate signal type for this
interface.
(Cisco MC3810 multiservice concentrator only)
Configures the voice-port compression mode. The
g729ar8 value is the default and is recommended.
On Cisco 2600 and 3600 series routers,
Note
codec configuration is performed on dial
peers. On all supported routers, codec
command options may vary depending
upon the voice card settings.
Selects the appropriate voice call progress tone for
this interface. Caller ID requires this setting. The
caller ID standard (Bellcore/Telcordia, ETSI,
ETSI-DTMF) is determined by this command.
On the Cisco MC3810 multiservice concentrator,
the default setting for locale is northamerica. On
Cisco 2600 and 3600 series routers, the default
setting for locale is us.
See
Table 57 on page 816
(Required on Cisco 2600 and 3600 series routers
FXS ports only) Selects the appropriate ring
frequency (in hertz) specific to the equipment
attached to this voice port.
(Optional on FXO ports only) Specifies an
attenuation other than the default of 14 dB (minus
14 dBm), enter a value of from 0 to 64, in decibels.
(Required on Cisco 2600 and 3600 series routers
FXO ports only) Specifies the maximum number
of rings to be detected before answering a call.
Command Option
Country
lu
Luxembourg
my
Malaysia
mx
Mexico
nl
Netherlands
for a list of options.