Acuity LITHONIA LIGHTING Aeris Suspend Series Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Beleuchtungskörper Acuity LITHONIA LIGHTING Aeris Suspend Series herunter. Acuity LITHONIA LIGHTING Aeris Suspend Series 3 Seiten.

Seite drucken

Installation Instructions

Aeris Suspend

WBA (Wall Bracket) INSTALLATION

OF WEATHER - PROOF CAULKING BETWEEN MOUNTING PLATE AND WALL TO

ENSURE WEATHER - TIGHT INTEGRITY OF ELECTRICAL COMPONENTS.

Tools Required: 3/16" allen wrench, 9/16" socket or wrench.

1. Secure base plate to wall with (4) 1/4" fastener (supplied by others) using the (4) holes

located on the outer corners of the base plate. Check the base plate to confirm that

it is level and plumb in all directions. (See figure 1).

2. Prepare the cover plate by attaching the Aeris mounting block to the cover plate using

(2) 3/8" diameter by 1-1/4" bolts with (2) 3/8" diameter lockwashers by inserting the bolts

and washers into the mounting block through the cover plate and thread into the

threaded steel bar stock. Use a 9/16" socket or wrench and tighten securely (See figure

2). When installing the fixture in the lens down position, place the curved portion of the

cover plate upwards . When installing the fixture in the lens up position (damp location

only), place the straight portion of the cover plate upwards.

3. Check the gasketing(factory installed) on the backside of the cover plate to ensure

that it is in place.

4. Place and tighten (4) 3/8" diameter by 1-1/4" stainless steel hex socket head screws

(requires 3/16" allen wrench) into the threaded opening of the cover plate by turning

approximately 6-7 full turns.

5. To prepare fixture for installation, refer to steps 2 and 3 per pole mounted instructions

on page 1.

6. Pull the wires from the fixture through the mounting block on the cover plate. Place

fixture onto the mounting block, being sure the wires are not being pinched.

7. Tighten the locking hex head bolt inside the arm with a 9/16" socket to 20-30 ft. lbs.

torque.

8. Make wiring connections, being careful to observe proper polarity and grounding.

9. Slide the assembly over the base plate, tighten the top (2) 3/8" x 1-1/4" stainless steel

hex socket head screws until 3/8" to 1/4" of the screw is still visible.

10. Tighten the bottom (2) 3/8" x 1-1/4" stainless steel hex socket head screws until 3/8"

to 1/4" of the screw is still visible.

11. Alternating between the top two and bottom two sets of screws, gently tighten until

snug, (approximately one thread showing on each screw).

12. Continue fixture installation and lamp installation (refer to step 6 per the pole mounted

instructions above).

13. Secure strut receiver to small strut wall mount plate using the 10-24 x 3/4" thread rolling

screw in the top hole on the center of the plate. The locating pin on the receiver should

sit in the second hole on the center of the plate (See Figure 3).

14. Attach aluminum rod using the two 1/4" x 1-1/4" black oxide screws to the receiver

on the top of the fixture and to the receiver on the wall mount plate using 5/32" allen

wrench. Tighten until head of screw is flush with the receiver block.

15. Secure the small strut wall mount plate to wall with two 1/4" fasteners (supplied by

others). Check the plate to confirm that it is level and plumb in all directions (See Figure

4).

CAUTION: APPLY A CONTINUOUS BEAD

Lithonia Lighting Outdoor

One Lithonia Way, Conyers, GA 30012

Phone: 800-279-8041 Fax: 770-918-1209

www.lithonia.com

Figure 1

(4) 1/4" fasteners

(by others)

Silicone

Seal

By others

Sealant by

Others

To wall

(4) Socket Held Screws

Figure 2

Figure 3

Strut

Receiver

Figure 4

Cover Plate

Gasket

(factory installed)

(4) Socket

Base Plate

Head Screws

Threaded

Steel Bar

Figure 2

Aeris Mounting Block

3/4" thread

rolling screw

1/4" black

oxide screws

Part Number: RJ5210199 Rev A

Revision Date: 3/4/08

Page 2

Stock