Cisco Profile Series Handbuch "Erste Schritte - Seite 18

Blättern Sie online oder laden Sie pdf Handbuch "Erste Schritte für Server Cisco Profile Series herunter. Cisco Profile Series 35 Seiten. Jbod on the 12g sas modular raid controller
Auch für Cisco Profile Series: Handbuch "Erste Schritte (41 seiten), Benutzerhandbuch (44 seiten), Benutzerhandbuch (7 seiten), Kurzreferenz-Handbuch (2 seiten), Installationshandbuch (44 seiten), Konfigurationshandbuch (13 seiten), Installationsblatt (2 seiten), Installationshandbuch (2 seiten), Schnellstart-Handbuch (4 seiten), Schnellstart-Handbuch (4 seiten), Handbuch zur Installation (16 seiten), Handbuch "Erste Schritte (32 seiten), Handbuch (16 seiten), Handbuch "Erste Schritte (42 seiten), Handbuch "Erste Schritte (46 seiten)

Seite drucken
Cisco Profile Series Handbuch
Cisco TelePresence Systems
GettinG started Guide
Table of contents
Introduction
touch controller
Configuring H.323 and SIP
To get online and ready to place and receive calls, your
system must be set up properly. Your system will use either
the H.323 protocol or the SIP protocol for video calls.
NOTE:
Contact your system administrator, or service
provider, for information about the network settings.
For networks administered through Cisco TMS (Cisco
TelePresence Management Suite) your Cisco TMS
administrator will help you to get online.
D14639.04 Video Systems Getting Started Guide (TC4.2) | 2011 JULY | © 2011 Cisco Systems, Inc. All rights reserved.
User interfaces
Configuration
Configuration
H.323
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Tap
More > Settings > Administrator settings > Network
Settings > H323 Settings
2. Enter the
H323 number
and
H323 id
input fields.
3. If you want to enter the address of the H.323 gatekeeper
manually, tap
Manual
in the
Gatekeeper discovery
section, and enter the
Gatekeeper address
field. Otherwise tap Auto.
4. If the H.323 gatekeeper requires authentication
and you want your system to authenticate itself to
the gatekeeper, tap
ON
in the
section and enter the
Login name
respective input fields. Otherwise, tap OFF.
5. Tap
Save
to save the changes, or
saving.
6. Tap
Back
twice to review the System Information page
and verify the H323 settings.
If you successfully registered to a Gatekeeper the
will show
Registered
in the H323 section.
7. Tap
Exit
to return to the home menu.
Appendices
SIP
If in doubt for any of the parameters below, contact your
system administrator or your service provider.
1. Tap
More > Settings > Administrator settings > Network
Settings > SIP Settings
in their respective
2. Enter the SIP URI in the
3. Tap the preferred transport protocol in the
transport
try to connect using TLS, then TCP, and finally UDP.
in the input
4. Choose a
proxy types by tapping the ‑ or + signs. The default type
is Standard.
5. If you want to enter the SIP proxy address manually,
Authentication mode
tap
Manual
and
Password
in the
Proxy address
to obtain the SIP proxy address automatically (DHCP),
Undo
to leave without
tap Auto.
6. If the SIP proxy server requires authentication you must
enter the
input fields to authenticate your system.
Status
7. Tap
Save
saving.
8. Tap
Back
and verify the SIP settings.
If you successfully registered to a SIP server the
will show
9. Tap
Exit
URI
input field.
Default
section. If you select Auto, the system will first
Proxy
type. Step through the list of available
in the
Proxy discovery
section and enter the
in the input field. If you want the system
Login name
and
Password
in the respective
to save the changes, or
Undo
to leave without
twice to review the System Information page
Status
Registered
in the SIP section.
to return to the home menu.
www.cisco.com
18