3Com OfficeConnect 3CR858-91 Installationshandbuch

Blättern Sie online oder laden Sie pdf Installationshandbuch für Netzwerk-Router 3Com OfficeConnect 3CR858-91 herunter. 3Com OfficeConnect 3CR858-91 2 Seiten. Cable/dsl router

Seite drucken

Installation Guide

OfficeConnect

Cable/DSL Router

(3CR858-91)

3Com Corporation. 350 Campus Drive, Marlborough, MA. USA 01752-3064

are registered trademarks of 3Com Corporation.

Microsoft, MS-DOS and Windows are registered trademarks of Micorsoft Corporation.

All other company and product names may be trademarks of their respective companies.

Part number: DIA8589-1AAA01 Published: June 2004

INTRODUCTION

About This Guide:

This Guide takes you through the basic steps necessary to install and configure

your OfficeConnect Cable/DSL Router, and establish a connection from your

computers to the Internet. Throughout, the OfficeConnect Cable/DSL Router

is simply referred to as the Router.

Your package contains:

●

One OfficeConnect Cable/DSL Router

One power adapter for use with the Router

●

Four rubber feet

One Ethernet cable

●

One CD-ROM containing the Router Discovery program and the User Guide

●

This Installation Guide

●

One Support and Safety Information Sheet

●

One Warranty Flyer

System Requirements

Before starting, you must ensure the following:

●

You already have a cable or DSL broadband connection to the Internet, with

a suitable modem, and that this connection works properly. The modem

must have an Ethernet port for connection to your Router.

●

You have a computer that has an Ethernet connection available and is

already correctly configured for communication with the Internet. Your

computer must be able to connect to the Internet via the modem, and must

have a Web browser installed.

●

There are no other DHCP server devices on your local network that are

responsible for allocating IP addresses to your computers and other network-

connected devices. Your Router will now perform this function by default.

If one or more of these conditions are not met, refer to the comprehensive Router

User Guide provided on the accompanying CD-ROM for further guidance.

ABOUT YOUR ROUTER

Cable/DSL Router - Front

1 Alert LED

the unit. To do this, remove power, wait 10 seconds and

then re-apply power. The Router will then enter the start-

Orange

up sequence and resume normal operation.

Indicates a number of different conditions, as described

On for 2 seconds, and then off - The Router has detected

below.

and prevented a hacker from attacking your network

Off - The Router is operating normally.

from the Internet.

Flashing quickly - Indicates one of the following

Continuously on - A fault has been detected with your

conditions:

Router during the start-up process. Refer to 'Problem

• The Router has just been started up and is running a

Solving' section.

self-test routine, or

2 Power LED

• The administrator has invoked the Reset to Factory

Green

Defaults command, or

Indicates that the Router is powered on.

• The system software is in the process of being

3 Four LAN Status LEDs

upgraded

Green (100Mbps link) / Yellow (10Mbps link)

In each of these cases, wait until the Router has

completed the current operation and the alert LED

If the LED is on, the link between the port and the next

is Off.

piece of network equipment is OK. If the LED is flashing,

the link is OK and data is being transmitted or received. If

Flashing slowly - The Router has completed the Reset to

the LED is off, nothing is connected, the connected

Factory Defaults process, and is waiting for you to reset

DIMENSIONS AND STANDARDS

Dimensions and Operating Conditions

Standards

Functional:

ISO 8802/3

EMC:

EN 55022 Class B

IEEE 802.3

EN 55024, CISPR 22

Safety:

UL60950, EN 60950

FCC Part 15 Class B*

CSA 22.2 #60950

ICES-003 Class B

IEC60950

ETSI EN 301 489-17

CNS 13438 Class A

Environmental:

EN 60068 (IEC 68)

* Refer to Regulatory Notices section in the Support and Safety Information sheet

OfficeConnect

Cable/DSL Router

7 VA, 23.9 BThU/hr

power requirement

0 to 40ºC (32 to 105ºF)

operating

temperature

0 to 90%

(non-condensing)

humidity

OfficeConnect

Cable/DSL Router

535g (1.3 lb)

Cable/DSL Router - Rear

device is switched off, or there is a problem with the

connection (refer to 'Problem Solving' section). The port

will automatically adjust to the correct speed and duplex.

4 Cable/DSL Status LED

Green (100Mbps link) / Yellow (10Mbps link)

If the LED is on, the link between the Router and the

cable or DSL modem is OK. If the LED is flashing, the link

is OK and data is being transmitted or received. If the LED

is off, nothing is connected, the modem is switched off

or there is a problem (refer to 'Problem Solving' section).

5 Power Adapter Socket

Only use the power adapter that is supplied with this

Router. Do not use any other adapter.

6 Ethernet Cable/DSL port

Use the supplied patch cable to connect the Router to

the Ethernet port on your cable or DSL modem. The

port will automatically adjust to the correct speed and

duplex.

POSITIONING YOUR ROUTER

Safety Information

WARNING: Please read the 'Important Safety Information' section in the

Support and Safety Information sheet before you start.

VORSICHT: Bitte lesen Sie den Abschnitt 'Wichtige Sicherheitsinformationen'

sorgfältig durch, bevor Sie das Gerät einschalten.

AVERTISSEMENT: Veuillez lire attentivement la section "Consignes importantes

de sécurité" avant de mettre en route.

When positioning your Router, ensure:

● It is out of direct sunlight and away from sources of heat.

● Cabling is away from power lines, fluorescent lighting fixtures, and sources

of electrical noise such as radios, transmitters and broadband amplifiers.

● Water or moisture cannot enter the case of the unit.

● Air flow around the unit and through the vents in the side of the case is

not restricted. We recommend you provide a minimum of 25mm (1in.)

clearance.

Using the Rubber Feet

Use the four self-adhesive rubber feet to prevent your Router from moving

around on your desk or when stacking with other flat top OfficeConnect units.

Only stick the feet to the marked areas at each corner of the underside of your

Router.

7 Four 10/100 LAN ports

Using suitable RJ-45 cable, you can connect your

Router to a computer, or to any other piece of

equipment that has an Ethernet connection (for

example, a hub or a switch). The LAN ports are

configured as MDIX, for connection to a computer with

a straight through RJ-45 cable.

8 Power Adapter OK LED

Green

Indicates that the power adapter is supplying power to

the Router. If the LED is off, there may be a problem with

the power adapter or adapter cable.