Cisco 2621XM Benutzerhandbuch - Seite 30
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Gateway Cisco 2621XM herunter. Cisco 2621XM 48 Seiten. Non-proprietary security policy
Auch für Cisco 2621XM: Betrieb (25 seiten), Benutzerhandbuch (20 seiten)
The Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, 3745, and 7206 VXR NPE-400 Routers
Place the third label on the router as shown in
Step 4
so that the half of the label covers the bottom of the enclosure and the other half covers the first WAN
interface card slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Step 5
Place the fourth label on the router as shown in
so that the half of the label covers the bottom of the enclosure and the other half covers the second WAN
interface card slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Step 6
Place the fifth label on the router as shown in
that the half of the label covers the bottom of the enclosure and the other half covers the third WAN
interface card slot. Any attempt to remove a WAN interface card will leave tamper evidence.
Place the sixth label on the router as shown in
Step 7
so that the half of the label covers the bottom of the enclosure and the other half covers the fourth WAN
interface card slot. Any attempt to remove a WAN interface card will leave tamper evidence.
The labels completely cure within five minutes.
Step 8
Figure 20
PW R
To apply serialized tamper-evidence labels to the Cisco 2621XM and Cisco 2651XM:
Step 1
Clean the cover of any grease, dirt, or oil before applying the tamper evidence labels. Alcohol-based
cleaning pads are recommended for this purpose. The temperature of the router should be above 10°C.
Step 2
Place the first label on the router as shown in
that the one half of the tamper evidence label covers the enclosure and the other half covers the side of
the router. Any attempt to remove the enclosure will leave tamper evidence.
Place the second label on the router as shown in
Step 3
so that the one half of the tamper evidence label covers the enclosure and the other half covers the side
of the router. Any attempt to remove the enclosure will leave tamper evidence.
Place the third label on the router as shown in
Step 4
that the one half of the label covers the enclosure and the other half covers the Network Module slot.
Any attempt to remove a Network Module will leave tamper evidence.
Cisco 1721, 1760, 2621XM, 2651XM, 2691, 3725, and 3745 Modular Access Routers and 7206-VXR NPE-400 Router FIPS 140-2 Non-Proprietary
30
Cisco 1721 and Cisco 1760 Tamper Evidence Label Placement
PWR
WIC 0
ACT /CH0
WIC 1
ACT /CH0
ETH
ACT
OK
ACT /CH1
ACT /CH1
COL
CON SOL
E
OK
PVD M 0
PVD M 1
MO D
OK
OK
OK
SLO T 0
0
OK
1
SLO T 1
0
OK
1
ACT
COL
FDX
100
LINK
10/1 00 ETH
ERN ET
AUX
Figure
20. The tamper evidence label should be placed
Figure
20. The tamper evidence label should be placed
Figure
20. The tamper evidence label should be placed so
Figure
20. The tamper evidence label should be placed
DSU
56K
SEE MANUAL BEFORE INSTALLATION
Model
WIC 0 OK
FDX
100
LINK
10/100 ETHERNET
Cisco 1721
Ci sc o 17
00
Se rie s
SLO T 2
0
1
OK
SLO T 3
0
1
OK
Figure
21. The tamper evidence label should be placed so
Figure
21. The tamper evidence label should be placed
Figure
21. The tamper evidence label should be placed so
AUX
MOD OK
WIC 1 OK
+5, +12, -12 VDC
OL-6083-01