Epson Stylus C82N Hier beginnen
Blättern Sie online oder laden Sie pdf Hier beginnen für Drucker-Zubehör Epson Stylus C82N herunter. Epson Stylus C82N 2 Seiten. Epson stylus c82n: quick start
Auch für Epson Stylus C82N: Broschüre & Specs (2 seiten), Produkt-Informationsblatt (4 seiten), Spezifikationen (2 seiten), Informationen zum Produkt (13 seiten)
Seite drucken
EPSON Stylus
®
Start
Start
Here
Here
1
1
Unpack
Unpack
1
Remove everything from the box.
Printer Basics
Printer
Paper support
AC adapter and
power cord for
print server
Print server
2
Remove all the blue tape and packing material inside and
around the printer. The tape may be in slightly different
places on your printer, so check carefully.
3
Slide the paper support into the grooves on
either side of the sheet feeder. The
paper support should
fit securely.
2
2
Power On
Power On
1
C82N
Plug the printer's power cord into a grounded electrical outlet.
2
Press the printer's
CAUTION: Use only the printer's
3
3
Load Ink
Load Ink
1
Lower the printer's output tray
and open the cover.
CPD-15266
2
Shake the package of ink cartridges four or five times. Then remove the cartridges
from the package. (Don't shake them after removing the packaging.)
Supplement
3
Lower each ink cartridge into its holder with the green circuit board facing the back.
booklet
Then gently push each ink cartridge down until it is firmly seated.
The color of the cartridge label should match the marker on the holder.
Printer software
CD-ROM
Ink cartridges
4
Press the
The green power light flashes as your printer charges ink for about 90 seconds.
CAUTION: Don't turn off the printer while the green power light is flashing
unless the printer hasn't moved or made any noise for more than 5 minutes.
power button until the green power light comes on.
Power button
power button to turn the printer on or off.
Don't touch the
green circuit boards
or remove any labels
ink button and close the printer cover.
Ink button
4
4
Load Paper
Load Paper
1
Fan a few sheets of paper and place
them against the right edge guide.
Don't push the paper in.
2
Slide the left edge guide against the paper,
but not too tightly.
3
Pull out the output tray extensions.
5
5
Connect the
Connect the
Print Server
Print Server
1
Turn off the printer.
2
Plug the print server into
the printer's parallel port.
Squeeze the wire clips
together until they lock
in place on either side
of the connector.
3
Connect the network cable to
the 10/100 connector on the
Print server
print server, and then connect
the other end of the cable
to a hub or switch. Use
a Category 5 twisted pair
straight-through cable with
RJ45 connectors.
NOTE: The print server will automatically use
10/100 connector
DHCP to obtain an IP address. If it cannot
get an IP address this way, it will use the
DCIN connector
private IP address of 192.168.192.168.
4
Plug the AC adapter into the DCIN
connector on the print server. Connect
the AC adapter's power cord to the
AC adapter.
5
Plug the power cord of the AC adapter into a
grounded electrical outlet. The lights on the print
server will turn on.
6
Press and hold down the status sheet button on the print server, and then turn on the
printer. Continue to hold down the status sheet button for about 5 seconds. The STATUS
light turns red as the print server initializes, while the DATA light beneath it stays green.
NOTE: It can take up to one minute to initialize the print server. When it is done
initializing, its STATUS light turns green or orange.
7
When the print server is done initializing, press the status sheet button again for about two
seconds to print a report that is two pages long. If the status report prints, the print server
is installed correctly.
CAUTION: Before disconnecting the print server from the printer, always turn off
the printer and unplug the AC adapter.
Turn over
Don't load paper
above this arrow
Status sheet
button
STATUS light
DATA light