Dimplex BF33STP Service-Handbuch - Seite 10

Blättern Sie online oder laden Sie pdf Service-Handbuch für Innenkamin Dimplex BF33STP herunter. Dimplex BF33STP 20 Seiten. Fireplace
Auch für Dimplex BF33STP: Praktisches Benutzerhandbuch (15 seiten), Benutzerhandbuch (14 seiten), Benutzerhandbuch (14 seiten), Handbuch zur Fehlersuche (2 seiten), Benutzerhandbuch (14 seiten), Installationshandbuch (14 seiten)

Seite drucken

the ember bed by the sides, pull firmly until the rear tab

pops out from under the back ledge, then lift the logs

out. (Figure 5)

IMPORTANT: Only handle the log-set by the plastic

ember-bed, not the logs themselves.

NOTE: Log-set fits tightly into firebox. Some force

may be necessary to remove.

Disconnect the log set LED wire harness from unit.

(DXP MODELS ONLY)

Remove all lower light bulbs.

Remove the 4 retaining screws on the lower light as-

sembly retaining plate and pull it away from the lower

panel.

Cut the blue and white light harness wires from the

old harness at the first socket, which lead inside the

firebox. Strip the ends leading inside the firebox by ap-

proximately a ½" (12.7 mm).

Remove the socket rings that hold the sockets to the

light assembly retaining plate by unscrewing the rings

counter clockwise.

Remove the old sockets and replace with the new

sockets and socket rings.

10.

Cut the metal ferrules off the end of the blue and white

wires from the new light harness and strip them by ap-

proximately a ½" (12.7mm).

11.

Using a wire-nut, connect the 2 matching wire ends

from the old and new harness, matching up the colors

(1-blue to 1-blue / 1-white to 1-white).

NOTE: Connection to the terminal block can only be

accessed through additional disassembly therefore an ad-

ditional electrical junction is recommended in the bottom

area.

12.

Reassemble in the reverse order as above.

NOTE: When re-inserting the log-set, insert the front

edge first then push the backside of the log-set down until

the rear tab snaps under the back partially reflective glass

ledge and the logs are resting against the partially reflective

glass.

LED DRIVER BOARD REPLACEMENT -

DXP MODELS ONLY

Tools Required: Phillips head screwdriver

Needle nose pliers

Flat head screwdriver

WARNINg: If the fireplace was operating prior to

servicing allow at least 10 minutes for light bulbs and

heating elements to cool off to avoid accidental burning

of skin.

WARNINg: Disconnect circuit power before attempt-

ing any maintenance or cleaning to reduce the risk of

electric shock or damage to persons.

Open the steel curtains (remove glass doors if appli-

cable).

Remove the 2 screws from the log set retaining plate

along the front of the log set and remove the retaining

plate.

Pull the rear edge of the log set forward by grasping

the ember bed by the sides (handle the log set only by

the ember bed and not the logs) and pulling firmly until

the rear tab pops out from under the back ledge, then

lift out. (Figure 5)

IMPORTANT: Only handle the log-set by the plastic

ember-bed, not the logs themselves.

NOTE: Log-set fits tightly into firebox. Some force

may be necessary to remove.

Disconnect the log set LED wire harness from unit.

Remove the light assembly retaining plate by removing

4 lower light bulbs and the retaining plate screws. Set

the retaining plate and light bulbs aside.

Reach hand into the opening created by removing the

light assembly retaining plate and locate the LED driver

board mounted on the lower right side on the back

panel.

Remove the wires attached to the board noting their

original location.

NOTE: Using a flat head screwdriver gently pry be-

tween the end of the connector and the switch to release

the wires.

Remove the driver board off the 4 mounting clips (one

on each corner of the board), by squeezing the tips of

the mounting clips with needle nose pliers. Squeeze

them just enough to pull the board off. These clips will

be re-used to secure the new board.

Line up the mounting holes on the new board to the

clips and press the new board in place.

10.

Install wires on new board in the original configuration.

11.

Re-assemble in reverse order as above.