Dimplex BLF7451-AU Gebrauchsanweisung - Seite 15

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Innenkamin Dimplex BLF7451-AU herunter. Dimplex BLF7451-AU 19 Seiten. Prism 1.2kw wall mounted electric fire
Auch für Dimplex BLF7451-AU: Benutzerhandbuch (19 seiten)

Seite drucken

Operation

Icon

Display

Function

Power /

Standby

Sleep

Timer

Flame Effect

Low

Flame

High

Flame

Demo

Mode

Off

Colour Theme

Theme 1

Theme

2-8

Bright-

ness

Heat

Low

Heat

High

Heat

Cool

Blow

Off

Temp

Down

Temp Up

Description

Press once to turn the product 'ON'.

Press a second time to put the product into 'STANDBY'

(When returning from 'STANDBY' mode the product will return to previous settings unless the

product has been plugged out, in which case it will reset to factory settings)

Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5 hr to 8.0 hr before

turning off. The remaining time on the 'SLEEP TIMER' displays. (This icon is Green in Colour)

'FLAME EFFECT' button cycles the unit sequentially through the 4 settings, LOW FLAME, HIGH

FLAME, DEMO MODE and OFF.

This setting will run the flame effect at a low brightness level. (The display will show F1)

This setting will run the flame effect at a high brightness level. (The display will show F2)

This setting will slowly pulse the flame effect between low and high brightness. (The display will

show FP)

This will turn the flame effect off. If the heater is running, the display will activate and remain active

to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.

'Colour Themes' are setting which change the colour of the fuel bed and there are eight different

themes

Theme 1 is a 'Demo Mode' - this setting will scroll through all of the colour settings, you can 'Pause'

this demo mode by pressing the 'Brightness Button' /

'Unpause' press the 'Brightness Button' /

Themes 2-8 are pre-set colours that remain static.

This button switches themes 2-8 between full brightness and half brightness. This button also

interacts with the product when set on theme as previously described above

'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL

BLOW and OFF. The heat setting will be indicated by an icon in the floating display see Fig. 2.

When the flame effect is 'ON' the floating display will turn off after 5 seconds, however if the

heater is being used independently of the flame effect. The low heat or high heat icon will appear

continuously in the floating display.

This setting will run the heater at 'LOW HEAT' - this setting will be indicated by the 'LOW HEAT'

icon and the letters 'LO' appearing in the display.

(This icon is Orange in Colour)

This icon in the floating display indicates 'HIGH HEAT' - this setting will be indicated by the 'HIGH

HEAT' icon and the letters 'HI' appearing in the display.

(This icon is Red in Colour)

This icon in the floating display indicates 'COOL BLOW' - this setting will be indicated by the 'COOL

BLOW' icon and the letters 'CB' appearing in the display.

(This icon is Blue in Colour)

This switches the heater and blower 'OFF', no icon will be displayed in the floating display. Note the

blower will run for 10-20 seconds after being turned off, this is to ensure the product cools down

safely.

Press multiple times to lower the heater temperature in 1ºC increments. The lowest temperature that

can be set 5ºC.

Note: Once you stop at your desired temperature, this will flash 3 times, then the display will show

the room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

Press multiple times to increase the heater temperature in 1ºC increments. The highest temperature

that can be set is 37ºC.

Note: Once you stop at your desired temperature, this will flash 3 times, then the display will show

the room temperature as detected by the product. If the set temperature is lower than the detected

room temperature the heater will not activate.

in which case the display will read

in which case display will read

1.p

1.U