Dimplex AC6N Installations- und Betriebsanleitung
Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Heizgerät Dimplex AC6N herunter. Dimplex AC6N 4 Seiten. Ac air curtains
Auch für Dimplex AC6N: Anleitung (3 seiten), Benutzerhandbuch (4 seiten), Installations- und Betriebsanleitung (12 seiten), Schnellstart-Handbuch (19 seiten), Handbuch (20 seiten)
Seite drucken
Dimplex Air Curtains
Models : AC3N, AC45N, AC6N &
Dimensions
(millimetres)
Model s
Watt
A
AC3N
3.0kw
605
AC45N
4.5kw
605
AC6N
6.0kw
905
AC3RN
3.0kw
605
(Remote control)
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
IMPORTANT SAFETY ADVICE
DO NOT COVER OR OBSTRUCT the air inlet or outlet
grille.
ENSURE THE APPLIANCE IS EARTHED.
Do not use this heater in areas where excessive dust
exists.
This heater must not be located immediately above
or below a fixed socket outlet or connection box.
Always disconnect supply before working on the
product.
This product should be mounted safely to solid wall
or ceiling surfaces only.
Ensure the supply cables are of adequate current car-
rying capacity and are protected by a suitable fuse.
If the appliance is mounted in a toilet or washroom,
the appliance should be mounted such that no part
of it can be touched by a person using a fixed bath or
shower.
If the appliance is mounted in a toilet or washroom
an isolating switch must be provided outside the
washroom adjacent to the entrance door.
Electrical
The installation of this appliance should be carried out by a
competent electrician and be in accordance with the current
IEE wiring regulations.
Fixing Positions
This appliance may be either wall-mounted or fixed to a ceil-
ing - see Fig. 2 for various fixing positions and 'Installation' for
details on fixing.
Heaters may be mounted end to end for wide doorways.
AC3RN
ceiling
Hole
Bracket
centres
length
B
C
424
492
424
492
721
756
424
492
Ceiling mounting
Wall mounting
Fig. 2
Installation and Operating Instructions
'C'
'B'
cable/conduit
'A'
entry
Front view
Installation
Using the wall mounting bracket as a guide (see Fig. 3) mark
off the hole positions on the wall or ceiling - a minimum height
of 1.8metres is required from floor to bracket. Fix the bracket
in position by following steps as described under the heading
'Wall or Ceiling Mounting'.
Wall or Ceiling Mounting
Solid brick or concrete block walls must be drilled and plugged
(using a spirit level as a guide ensure bracket is level) with
rawlplug No. 8 size fibre inserts. The plug must be located in
the solid part of the wall, not just in the plaster layer.
For panelled internal walls or ceilings, it is best to locate the
studding, position the heater fixing bracket accordingly and
use No. 8 size wood screws. If it is not possible to locate the
studding, use type M5 Rawlplug inserts, making the 10mm
holes with a drill rather than a bradawl or a screwdriver.
It is important that the serrated metal washer is located be-
tween the heater holding bracket and the wall mounting
bracket. Adjust heater to the required angle then firmly tighten
the fixing screws inside the endcap using a cross-head screw-
driver as shown in Fig. 4.
access hole for
screwdriver
serrated washer
Detail view of Wall fixing bracket arrangement
08/18848/1
50
ceiling mtd.
45
214
135
Side views
Locate the heater
on the mounting
bracket ensuring
that the pozi-head
screws are fully en-
wall
gaged in the slots
mounting
of the bracket.
bracket
Fig. 3
wall
mounting
holding bracket
bracket
fixing screw
Issue 1
wall mtd.
200
155
Fig. 1
Fig. 4