CRU RTX115DC-3Q Schnellstart-Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Gehege CRU RTX115DC-3Q herunter. CRU RTX115DC-3Q 2 Seiten.
Seite drucken2. HDD Installation
2.1 RTX100-3Q and RTX Secure 110-3Q
a. Pull the ejection handle, open the door.
b. Slide in your SATA hard drive, connector-end first.
c. Shut the door until you hear it click.
2.2 RTX111-3Q, RTX Secure 111-3Q, and RTX112-3Q
a. Slide the drive carrier out of the RTX.
b. The carrier's cover is held in place by a screw on the rear of the carrier.
Remove the screw then remove the cover.
c. Slide the drive in from the front of the carrier.
d. Mate the connection on the drive with the connection on the drive
carrier circuit board.
e. Flip the drive/carrier assembly over, while holding the HDD in place.
Secure the drive in place with the provided screws.
f. Attach the Temperature Control Cooling Sensor to the top of the drive
with an adhesive strip.
g. Replace the carrier cover and secure the screw on the rear of the carrier.
h. Slide the carrier into the RTX.
*A flashing green LED on the bay indicates bay fan failure. Call CRU technical
support.
2.3 RTX115-3Q and RTX115DC-3Q
a. Slide the drive carrier out of the frame.
b. The carrier's cover is held in place by two screws—one on either side of
the carrier. Remove these screws then remove the cover.
c. Insert the drive into the carrier.
d. Mate the connection on the drive with the connection on the drive
carrier circuit board.
e. Flip the drive/carrier assembly over, while holding the HDD in place.
Secure the drive in place with the provided screws.
f. Replace the drive cover and secure the screw on the rear of the carrier.
g. Slide the carrier into the frame assembly.
*Flashing red and blue LEDs on the bay indicate bay fan failure. Call CRU
technical support.
3. Connecting and Powering
RTX-3Q can connect to your computer in one of several ways (eSATA, FireWire
800, USB 2.0 and USB 3.0). Choose one of those cables to use and plug it into
the product. Connect the power cord to the product and to a grounded electrical
outlet.
NOTE: To connect RTX-3Q to a USB 2.0 host,
you must use the included USB 2.0 cable.
For models with encryption, ensure that the encryption key is inserted and that
the lock on the bay is in the 'locked" position.
Switch the product on. The drive will spin up automatically on RTX100-3Q and
RTX115DC-3Q. The key lock needs to be in the "locked" position for RTX Secure
110-3Q, RTX111-3Q, RTX Secure 111-3Q and RTX112-3Q to spin up. For RTX115-
3Q, press the power button to spin up the drive.
Your RTX 1-Bay-3Q is now ready to use!
4. Encryption Information (models with encryption only)
RTX-3Q with encryption uses full disk hardware encryption to encrypt the entire
contents of the drive—including the boot sector, operating system and all files—
without performance degradation.
The Security Key must be installed prior to powering on the RTX-3Q for the data
to be decrypted on the drive. Externally connected Security Keys may be removed
and stored in a safe location once they have been accepted. Always store Security
Keys apart from the data so that in the event that the drive is lost or stolen, the
data is protected.
When a drive is formatted using an encryption key, the same or a duplicate key
must be used in order to access the data. There is no "back door" to access the
data; lost keys make data recovery virtually impossible.
WARNING: Never plug an encryption key into
a mini-USB port or a mini-USB product into the
encryption key port.
CRU Mark
10.25.12
PMS 711
2 cyan
85 magenta
76 yellow