Pioneer DEH-1300MP Benutzerhandbuch - Seite 6

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Auto-Empfänger Pioneer DEH-1300MP herunter. Pioneer DEH-1300MP 28 Seiten. Cd receiver, autoradio cd, radio cd
Auch für Pioneer DEH-1300MP: Benutzerhandbuch (21 seiten)

Seite drucken

Section

Installation

Connections

WARNING

! Use speakers over 50 W (output value) and be-

tween 4 W to 8 W (impedance value). Do not

use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately), make

sure to connect the ground wire first. Ensure

that the ground wire is properly connected to

metal parts of the car's body. The ground wire

of the power amp and the one of this unit or

any other device must be connected to the car

separately with different screws. If the screw

for the ground wire loosens or falls out, it

could result in fire, generation of smoke or

malfunction.

POWER AMP

Ground wire

Other devices

Metal parts of car's body

(Another electronic

device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position

No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result

in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the

battery before installation.

— Secure the wiring with cable clamps or ad-

hesive tape. Wrap adhesive tape around

wiring that comes into contact with metal

parts to protect the wiring.

— Place all cables away from moving parts,

such as the gear shift and seat rails.

— Place all cables away from hot places,

such as near the heater outlet.

— Do not connect the yellow cable to the bat-

tery by passing it through the hole to the

engine compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. The current capacity of

the cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable di-

rectly to ground.

— Never band together negative cables of

multiple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an exter-

nal power amp or the vehicle's auto-antenna

relay control terminal (max. 300 mA 12 V DC).

If the vehicle is equipped with a glass anten-

na, connect it to the antenna booster power

supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal of

the auto antenna. Doing so may result in bat-

tery drain or a malfunction.

Installation

This unit

2 3

1 Antenna input

2 Fuse (10 A)

3 Power cord input

4 Rear output

Power cord









1 To power cord input

2 Left

3 Right

4 Front speaker

5 Rear speaker

6 White

7 White/black

8 Gray

9 Gray/black

a Green

b Green/black

c Violet

d Violet/black

e Black (chassis ground)

Connect to a clean, paint-free metal location.

f Yellow

Connect to the constant 12 V supply terminal.

g Red

Connect to terminal controlled by ignition

switch (12 V DC).

h Blue/white

Connect to system control terminal of the

power amp or auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Note

With a 2 speaker system, do not connect anything

to the speaker leads that are not connected to

speakers.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.





1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

3 Connect with RCA cables (sold separately)

4 To Rear output

5 Rear speaker

Installation

Important

! Check all connections and systems before

final installation.

! Do not use unauthorized parts as this may

cause malfunctions.

! Consult your dealer if installation requires dril-

ling of holes or other modifications to the vehi-

cle.

! Do not install this unit where:

— it may interfere with operation of the vehi-

cle.

— it may cause injury to a passenger as a re-

sult of a sudden stop.

Section