Pioneer DEH-15MP Benutzerhandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Auto-Empfänger Pioneer DEH-15MP herunter. Pioneer DEH-15MP 44 Seiten. Cd rds receiver

Seite drucken

Operating this unit

Selecting a source

1 Press SRC/OFF to cycle between:

TUNER (tuner)—CD (CD player)—AUX (AUX)

Adjusting the volume

1 Turn M.C. to adjust the volume.

CAUTION

For safety reasons, park your vehicle when re-

moving the front panel.

Note

When this unit's blue/white lead is connected to

the vehicle's auto-antenna relay control termi-

nal, the vehicle's antenna extends when this

unit's source is turned on. To retract the anten-

na, turn the source off.

Use and care of the remote

control

Using the remote control

1 Point the remote control in the direction of the

front panel to operate.

When using for the first time, pull out the film

protruding from the tray.

Replacing the battery

1 Slide the tray out on the back of the remote

control.

2 Insert the battery with the plus (+) and minus

(–) poles aligned properly.

WARNING

! Keep the battery out of the reach of children.

Should the battery be swallowed, consult a

doctor immediately.

! Batteries (battery pack or batteries installed)

must not be exposed to excessive heat such

as sunshine, fire or the like.

CAUTION

! Use one CR2025 (3 V) lithium battery.

! Remove the battery if the remote control is

not used for a month or longer.

! There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the

same or equivalent type.

! Do not handle the battery with metallic tools.

! Do not store the battery with metallic ob-

jects.

! If the battery leaks, wipe the remote control

completely clean and install a new battery.

! When disposing of used batteries, comply

with governmental regulations or environ-

mental public institutions' rules that apply in

your country/area.

! "Perchlorate Material – special handling may

apply.

See www.dtsc.ca.gov/hazardouswaste/

perchlorate. (Applicable to California,

U.S.A.)"

Important

! Do not store the remote control in high tem-

peratures or direct sunlight.

! The remote control may not function properly

in direct sunlight.

! Do not let the remote control fall onto the

floor, where it may become jammed under

the brake or accelerator pedal.

Operating this unit

Frequently used menu

operations

Returning to the previous display

Returning to the previous list (the folder one level

higher)

1 Press

/DIMMER.

Returning to the ordinary display

Canceling the main menu

1 Press BAND.

Returning to the ordinary display from the list

1 Press BAND.

Tuner

Basic operations

Selecting a band

1 Press BAND until the desired band (FM1,

FM2, FM3 for FM or AM) is displayed.

Switching preset stations

1 Press c or d.

! Select PCH (preset channel) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

the next page.

Manual tuning (step by step)

1 Press c or d.

! Select MAN (manual tuning) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

the next page.

Seeking

1 Press and hold c or d, and then release.

You can cancel seek tuning by briefly pressing

c or d.

While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as

you release c or d.

Storing and recalling stations

for each band

Using preset tuning buttons

When you find a station that you want

to store in memory, press one of the preset

tuning buttons (1/

to 6/

) and hold until

the preset number stops flashing.

Press one of the preset tuning buttons

(1/

to 6/

) to select the desired station.

Switching the display

Selecting the desired text information

1 Press DISP to cycle between the following:

! BRDCST INFO (program service name/

song title/artist name)

! FREQUENCY (frequency)

! CLOCK (source name and clock)

Notes

! BRDCST INFO text information will change

automatically.

! Depending on the band, text information can

be changed.

! Text information items that can be changed

depend on the area.

Function settings

Press M.C. to display the main menu.

Turn M.C. to change the menu option

and press to select FUNCTION.

Turn M.C. to select the function.

Once selected, the following functions can be

adjusted.

Section