Pioneer DEH-4300UB Benutzerhandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Auto-Empfänger Pioneer DEH-4300UB herunter. Pioneer DEH-4300UB 17 Seiten. Cd rds receiver
Auch für Pioneer DEH-4300UB: Benutzerhandbuch (49 seiten)

Seite drucken

Sectlon

lID (

Installation

)

SectJon

(~I_n_st_a_lI_a_ti_o_n

Notes

• With a 2 speaker system, do not connect any-

thing to the speaker leads that are not con-

nected to speakers.

•

Change the initial setting of this unit. Refer to

SW CONTROL

(rear output and subwoofer set-

ting) on page 12.

The subwoofer output of this unit is monaural.

Left

Right

:1)

Front speaker

Rear speaker

White

(J) White/black

Gray

Gray/black

Green

Green/black

Violet

VioleVblack

@ Black (chassis ground)

Connect to a clean, paint-free metal location.

Yellow

Connect to the constant 12 V supply terminal.

Red

Connect to terminal controlled by ignition

switch (12V DC).

Blue/white

Connect to system control terminal of the

power amp or auto-antenna relay control

terminal (max. 300 mA 12 V DC).

Subwoofer (4

When using a subwoofer of 70 W (2

0),

sure to connect the subwoofer to the violet

and violeVblack leads of this unit. Do not con-

nect anything to the green and green/black

leads.

Not used.

Subwoofer

(40)

x 2

~®

~.@)_

_ ..

@ ~

:~--~-~

_~.~._._~

I-----u-.~,@

! - - - - - , @

I - - - - - - I @

I . . . - - - - I @

Perform these connections when using a sub-

woofer without the optional amplifier.

Power cord input

Rear output or subwoofer output

Front output

Only for DEH-4300UB

:1)

Antenna input

Fuse (10A)

Wired remote input

Only for DEH-4300UB.

Hard-wired remote control adaptor can be

connected (sold separately).

Power cord

Perform these connections when not connect-

ing a rear speaker lead to a subwoofer.

To power cord input

Disconnect the negative terminal of the

battery before installation.

Secure the wiring with cable clamps or ad-

hesive tape. Wrap adhesive tape around

wiring hat comes into contact with metal

parts to protect the wiring.

Place all cables away from moving parts,

such as the gear shift and seat rails.

Place all cables away from hot places,

such as near the heater outlet.

Do not connect the yellow cable to the bat-

tery by passing it through the hole to the

engine compartment.

Cover any disconnected cable connectors

with insulating tape.

Do not shorten any cables.

Never cut the insulation of the power cable

of this unit in order to share the power

with other devices. The current capacity of

the cable is limited.

Use a fuse of the rating prescribed.

Never wire the negative speaker cable di-

rectly to ground.

Never band together negative cables of

multiple speakers.

• When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an exter-

nal power amp or the vehicle's auto-antenna

relay control terminal (max. 300 mA 12 V DC).

If the vehicle is equipped with a glass anten-

na, connect it to the antenna booster power

supply terminal.

•

Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal of

the auto antenna. Doing so may result in bat-

tery drain or a malfunction.

This unit

No ACC position

Metal parts of car's body

ACC position

Other devices

(Another eledronic

device in the car)

Connections

AWARNING

Use speakers over 50 W (output value) and be-

tween 4

to 8

(impedance value). Do not

use 1

to 3

speakers for this unit.

The black cable is ground. When installing

this unit or power amp (sold separately), make

sure to connect the ground wire first. Ensure

that the ground wire is properly connected to

metal parts of the car's body. The ground wire

of the power amp and the one of this unit or

any other device must be connected to the car

separately with different screws. If the screw

for the ground wire loosens or falls out. it

could result in fire, generation of smoke or

malfunction.

Ground wire

POWER AMP

".'~

!>'ltW

c.:.> c.:.>

•

Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may result

in a fire or malfunction.

• To prevent a short-circuit. overheating or mal-

function, be sure to follow the directions

below.

~Important

• When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

CID