Pioneer DEH-7300BT Benutzerhandbuch - Seite 11

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Auto-Empfänger Pioneer DEH-7300BT herunter. Pioneer DEH-7300BT 23 Seiten. Cd rds receiver
Auch für Pioneer DEH-7300BT: Betriebshandbuch (29 seiten), Installationshandbuch (29 seiten)

Seite drucken

Operating this unit

Bluetooth telephone data can be deleted. To pro-

tect personal information, we recommend deleting

this data before transferring the unit to other per-

sons. The following settings will be deleted.

! phone book entries on the Bluetooth tele-

phone

! preset numbers on the Bluetooth telephone

! registration assignment of the Bluetooth tele-

phone

! call history of the Bluetooth telephone

! information of the connected Bluetooth tele-

phone

1 Press M.C. to show the confirmation display.

YES is displayed. Clearing memory is now on

standby.

If you do not want to reset phone memory,

press

. The display reverts.

2 Press M.C. to clear the memory.

CLEARED is displayed and the settings are de-

leted.

! While this function is in use, do not turn

off the engine.

VER INFO (Bluetooth version display)

You can display the system versions of this unit

and of Bluetooth module.

1 Press M.C. to display the information.

S/W UPDATE (updating the software)

This function is used to update this unit with the

latest software. For information on the software

and updating, refer to our website.

! Never turn the unit off while the software is

being updated.

1 Press M.C. to display the data transfer mode.

Follow the on-screen instructions to finish up-

dating the software.

Using an AUX source

Insert the stereo mini plug into the AUX

input jack.

Press S (SRC/OFF) to select AUX as the

source.

Note

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on the previous page.

Turning the clock display on

or off

% Press

to turn the clock display on or

off.

# The clock display disappears temporarily when

you perform other operations, but the clock display

appears again after 25 seconds.

Installation

Connections

WARNING

! Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do

not use 1 W to 3 W speakers for this unit.

! The black cable is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire first.

Ensure that the ground wire is properly con-

nected to metal parts of the car's body. The

ground wire of the power amp and the one of

this unit or any other device must be con-

nected to the car separately with different

screws. If the screw for the ground wire loos-

ens or falls out, it could result in fire, genera-

tion of smoke or malfunction.

POWER AMP

Ground wire

Other devices

Metal parts of car's body

(Another electronic

device in the car)

Important

! When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

ACC position

No ACC position

! Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may re-

sult in a fire or malfunction.

! To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

— Place all cables away from moving parts,

such as the gear shift and seat rails.

— Place all cables away from hot places, such

as near the heater outlet.

— Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.

— Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.

— Use a fuse of the rating prescribed.

— Never wire the negative speaker cable directly

to ground.

— Never band together negative cables of multi-

ple speakers.

! When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle's auto-anten-

na relay control terminal (max. 300 mA 12 V

DC). If the vehicle is equipped with a glass

antenna, connect it to the antenna booster

power supply terminal.

! Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

Section