Pioneer DEH-P3800MP - Radio / CD Installationshandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Installationshandbuch für Auto-Empfänger Pioneer DEH-P3800MP - Radio / CD herunter. Pioneer DEH-P3800MP - Radio / CD 8 Seiten. Owner's manual
Auch für Pioneer DEH-P3800MP - Radio / CD: Benutzerhandbuch (34 seiten)

Seite drucken

Installation

Note:

• Before making a final installation of the unit, tem-

• If installation angle exceeds 60° from horizontal,

porarily connect the wiring to confirm that the con-

the unit might not give its optimum performance.

nections are correct and the system works proper-

(Fig. 4)

ly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts

can cause malfunctions.

60°

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications

of the vehicle.

• Install the unit where it does not get in the driver's

way and cannot injure the passenger if there is a

sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot —

for instance, near a heater outlet.

DIN Front/Rear-mount

This unit can be properly installed either from "Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Holder

After inserting the holder into the dash-

board, then select the appropriate tabs

according to the thickness of the dash-

Dashboard

board material and bend them.

(Install as firmly as possible using the

182

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

Rubber bush

Screw

Removing the Unit (Fig. 6) (Fig. 7)

Frame

To remove the frame, extend top and bottom

of the frame outwards in order to unlock it.

(When reattaching the frame, point the side

with a groove downwards and attach it.)

• It becomes easy to remove the frame if

the front panel is released.

Fig. 4

Insert the supplied extraction keys

into the unit, as shown in the figure,

until they click into place. Keeping

the keys pressed against the sides of

the unit, pull the unit out.

Fig. 5

DIN Rear-mount

Installation using the screw holes on the side of the unit

1. Remove the frame. (Fig. 8)

Frame

Fig. 6

2. Fastening the unit to the factory radio mounting bracket.

(Fig. 9) (Fig. 10)

Select a position where the screw holes of the bracket and

the screw holes of the head unit become aligned (are fitted),

and tighten the screws at 2 places on each side. Use either

truss screws (5 × 8 mm) or flush surface screws

(5 × 9 mm), depending on the shape of the screw holes in

the bracket

Fig. 7

Screw

Factory radio mounting bracket

Fixing the Front Panel

If you do not operate the removing and attaching the front panel function, use the supplied fixing screws and

holders to fix the front panel to this unit.

1. Attach the holders to both sides of the front panel. (Fig. 11)

To remove the frame, extend top and bot-

tom of the frame outwards in order to

unlock it. (When reattaching the frame,

point the side with a groove downwards

and attach it.)

• It becomes easy to remove the frame if

the front panel is released.

2. Replace the front panel to the unit. (Fig. 12)

Fig. 8

3. Flip the holders into upright positions. (Fig. 13)

Fig. 9

4. Fix the front panel to the unit using fixing screws. (Fig. 14)

Dashboard or Console

Fig. 10

Holder

Fig. 11

Fig. 12

Fig. 13

Fixing screw

Fig. 14