Pioneer Super Tuner IIID MVH-P8200BT Installationshandbuch - Seite 6

Blättern Sie online oder laden Sie pdf Installationshandbuch für Auto-Empfänger Pioneer Super Tuner IIID MVH-P8200BT herunter. Pioneer Super Tuner IIID MVH-P8200BT 8 Seiten. Media center receiver

Seite drucken

Installation

English
Installation with the mounting
Note
sleeve
• Check all connections and systems before final
installation.
1. Insert the mounting sleeve into the
• Do not use unauthorized parts. The use of
dashboard.
unauthorized parts may cause malfunctions.
• When installing in a shallow space, use a
• Consult with your dealer if installation requires
supplied mounting sleeve. If there is enough
drilling of holes or other modifications of the
space behind the unit, use factory supplied
vehicle.
mounting sleeve.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result of
2. Secure the mounting sleeve by
a sudden stop.
using a screwdriver to bend the
• Install this unit away from hot places such as near
metal tabs (90°) into place.
the heater outlet.
• Optimum performance is obtained when the unit
Dashboard
is installed at an angle of less than 60°.
60°
• When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.
Mounting sleeve
Leave ample space
Dashboard
10cm (3-7/8 in.)
10cm (3-7/8 in.)
Installation
English
3. Install the unit as illustrated.
Removing the Unit
• Use commercially available parts when
1. Press the detach button to release
installing.
the front panel.
Nut
• Refer to the Operation Manual about how to
release the front panel.
Firewall or
metal support
2. Insert the supplied extraction keys
into both sides of the unit until
Metal strap
Screw
they click into place.
3. Pull the unit out of the dashboard.
Screw (M4 8)
• Make sure that the unit is installed securely
in place. Unstable installation may cause this
Fastening the front panel
unit to malfunction, such as sound skip.
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
Installation
English
Installing the microphone
2. Install the microphone clip on the
sun visor.
(MVH-P8200BT only)
• With the sun visor up, install the microphone
clip. (Lowering the sun visor reduces the voice
Installation notes
recognition rate.)
Install the microphone in a position and
Microphone clip
orientation that will enable it to pick up the
voice of the person operating the system.
CAUTION
• It is extremely dangerous to allow the microphone
lead to become wound around the steering
column or gearstick. Be sure to install the unit in
such a way that it will not obstruct driving.
When installing the microphone
on the sun visor
Clamp
1. Install the microphone on the
Use separately sold
clamps to secure the
microphone clip.
lead where necessary
inside the vehicle.
Microphone
When installing the microphone
Microphone clip
on the steering column
1. Install the microphone on the
microphone clip.
Microphone
Microphone base
Microphone clip
Fit the
microphone lead
into the groove.
• Microphone can be installed without using
microphone clip. In this case, detach the
microphone base from the microphone
clip. To detach the microphone base from
microphone clip, slide the microphone base.
Installation
English
2. Install the microphone clip on the
steering column.
Double-sided tape
Install the microphone clip on the
rear side of the steering column.
Clamp
Use separately sold
clamps to secure
the lead where
necessary inside the
vehicle.
Adjusting the microphone
angle
The microphone angle can be adjusted.